Coralline algae that form rhodoliths are widespread globally and their skeletal growth patterns have been used as (paleo-) environmental proxies in a variety of studies. However, growth interruptions (hiati) within their calcareous skeletons are regarded as problematic in this context. Here we investigated how hiati in the growth of Arctic rhodoliths from the Svalbard archipelago correspond to their environment and morphology. Using X-ray micro-computed tomography and stepwise model selections, we found that rhodoliths from deeper waters are subject to more frequent hiatus formation. In addition, rhodoliths with a higher sphericity (i.e., roundness) are less often affected by such growth interruptions. We conclude that these correlations are mainly regulated by hydrodynamics, because, in deeper waters, rhodoliths are not turned frequently enough to prevent a dieback of coralline algal thalli forming on the underside of the rhodolith. In this coherence, spheroidal rhodoliths are turned more easily, therefore shortening the amount of time between turnover events. Moreover, the incidence of light is more advantageous in shallower waters where rhodoliths exhibit a greater share of their surface to diffused ambient light, thus enabling thallus growth also on the down-facing surface of the rhodoliths. In consequence, information on the frequency of hiatus formation combined with rhodolith morphology might serve as a valuable proxy for (paleo-)environmental reconstructions in respect to light availability and the hydrodynamic regime.
17 June 2021 in Palaeobiodiversity and Palaeoenvironments
Bryostromatolites are found in stressed environments from the Paleozoic to the Recent. They are formed by alternating layers of bryozoans and microbes. This study investigates recent bryostromatolites in brackish ponds in the Netherlands to better understand ancient analogues and the environments which hosted them. They formed a fringing reef at the site Ronde Weel and a barrier reef at Kaaskenswater. The ponds had low biodiversity with only one bivalve species, two gastropod species, one ostracod species, and three diatom species comprising most of the easily fossilizable taxa; one isopod species, one decapod species, and two polychaete species were also present. Observations of microbial layers and cementation practices indicate that an alternation of bryozoan-favouring conditions and microbe-favouring conditions is essential to forming bryostromatolites. The collected bryostromatolites only had tiny living bryozoan patches. Water tests confirmed a brackish environment but with enriched arsenic and titanium concentrations and periodic euxinia. The extreme environment explains the lack of biodiversity and may provide information about the environments in which past bryostromatolites formed.
The electrolyte/solid interface is ubiquitous in nature and for many applications. In particular, the double‐layer properties are essential for predicting adsorption and transport behavior. While for small colloidal particles, electrophoretic mobility has developed into a routine technique, there is currently a lack of analogously established techniques for particles with diameters larger than 10 microns. Such particles are often encountered in natural soils, industrial formulations, and as contaminants in the form of microplastics. Herein, a systematic method development using the streaming potential technique of particle plugs composed of large particles is presented. This approach revives an analytical method that was first introduced nearly 75 years ago, which has rarely been used for particulate systems. Comparing the zeta‐potential versus pH of polystyrene particles with varying surface functionalization demonstrated that streaming potential measurements can distinguish these surface groups. In agreement with theoretical predictions, no dependence on the particle dimensions and shape is observed. Moreover, the particle arrangement within the particle plugs has been characterized by X‐ray microtomography. The viability of this technique is tested by monitoring the artificial weathering of artificially fragmented microplastic particles of non‐spherical shape. This technique opens new possibilities for characterizing the interfacial properties of environmentally relevant microplastics.
We show that halide evaporation during melt growth of on polycrystalline FTO under partially open conditions drives discrete phase selection between the line compounds of the CsBr–PbBr2 system, producing a sharp bilayer instead of compositional grading. In situ optical imaging shows that solidification begins with nucleation and lateral growth of a planar single crystal while the melt layer is still thick enough to average over the FTO relief. As the crystal thickens, the residual melt then becomes inhomogeneous and unstable, producing a buried porous layer of faceted grains with a characteristic in-plane spacing of 1–10). This morphology is consistent with a faceted Mullins–Sekerka-type instability under a non-conservative evaporative boundary condition. Beneath the single-crystal cap, the first-formed faceted islands are large and become progressively smaller as the advancing front approaches the FTO pyramids, while elevated ambient halide partial pressure suppresses the instability, consistent with diffusion–capillarity selection under decreasing residual melt thickness and steepening local gradients, modified by evaporative flux. Oxygen associated with microvoids or the oxide substrate enables a secondary reaction–diffusion pathway forming Pb–Br–O crystallites without altering the primary length scale. These results identify evaporation as an active control parameter coupling phase equilibria and interfacial stability in volatile halide melts. In the buried, porous bilayer morphology observed here, the secondary phases and porosity reduce the active volume and are expected to degrade scintillation through increased trapping, nonradiative recombination, and light scattering.
Introduction: Zirconia is a promising alternative to titanium dental implants, offering good osseointegration and aesthetics, but early clinical use has shown notable fracture rates linked to processing flaws, design issues, and biomechanical overloading. The aim of this study was to complement a prospective clinical trial reporting a 24.2% five-year failure rate due to implant fractures, and to systematically identify the reasons for fracture using fractographic and numerical approaches.Materials & Methods: Four retrieved, horizontally fractured zirconia implants (ZV3 implants) were examined using SEM fractography, surface profilometry, and micro-CT to characterize fracture origins, surface roughness, and porosity. Finite element analysis modelled stress distribution under horizontal loading, varying bone support levels and occlusal loading angles in relationship to axial offset.Results: All implants fractured palatal-to-buccal, originating at the root of the first endosseous thread. SEM revealed extensive pressing-related volume defects and severe surface grinding damage due to the subtractive milling and sandblasting procedures. Surface roughness (Rz) was 15 ± 7 µm; micro-CT revealed a defect size frequency peaking at 30 µm, although reaching up to 50 - 70 µm. FEA showed peak stress of 554 MPa at the fracture site under a 600 N applied loading, rising to 1376 MPa with 3 mm simulated bone loss. A simulated lateral crown alignment with the implant axis of 1 mm, further reduced the maximum principal stress at the fracture site by about 100 MPa.Discussion: Fracture mechanics estimations have shown that the measured critical defects could have reduced fracture strength from a theoretical ~ 1200 MPa to 800 - 430 MPa, which could have been sufficient to trigger clinical failures. Stress concentration in the root of the first thread, combined with bone loss and off-axis loading led to increased risk for fracture. Conclusions: Implant fracture resulted from pressing and surface machining defects interacting with a stress-concentrating thread geometry, aggravated by bone loss and off-axis loading. These findings highlight the importance of material quality, implant design, and optimal surgical and prosthetic planning.
About Me
Focused on lower jurassic stratigraphy and palecology, but open to any kind of interesting research.
Focused on lower jurassic stratigraphy and palecology, but open to any kind of interesting research.