Pawel Gasior

Dr. Pawel Gasior

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 June 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PGPawel Gasior
Pawel Gasior
KWKarol Wachtarczyk
Karol Wachtarczyk
ABAleksander Błachut
Aleksander Błachut
JKJerzy Kaleta
Jerzy Kaleta
NYNeha Yadav
Neha Yadav
ABAmelie Baron
Amelie Baron
A polyethylene (PE) liner is the basic element in high-pressure type 4 composite vessels designed for hydrogen or compressed natural gas (CNG) storage systems. Liner defects may result in the elimination of the whole vessel from use, which is very expensive, both at the manufacturing and exploitation stage. The goal is, therefore, the development of efficient non-destructive testing (NDT) methods to test a liner immediately after its manufacturing, before applying a composite reinforcement. It should be noted that the current regulations, codes and standards (RC&S) do not specify liner testing methods after manufacturing. It was considered especially important to find a way of locating and assessing the size of air bubbles and inclusions, and the field of deformations in liner walls. It was also expected that these methods would be easily applicable to mass-produced liners. The paper proposes the use of three optical methods, namely, visual inspection, digital image correlation (DIC), and optical fiber sensing based on Bragg gratings (FBG). Deformation measurements are validated with finite element analysis (FEA). The tested object was a prototype of a hydrogen liner for high-pressure storage (700 bar). The mentioned optical methods were used to identify defects and measure deformations.

23 December 2021 in Materials
Verified
Journal Article
Open access
PDF file
KWKarol Wachtarczyk
Karol Wachtarczyk
PGPawel Gasior
Pawel Gasior
JKJerzy Kaleta
Jerzy Kaleta
AAAlicja Anuszkiewicz
Alicja Anuszkiewicz
MBMarcel Bender
Marcel Bender
Tomasz OsuchTomasz Osuch
Tomasz Osuch
In this paper, the application of a fiber Bragg grating written in a highly birefringent side-hole elliptical core optical fiber for two-axial strain measurement is presented. Hybrid optical fiber structures achieved by combining large side-holes and elliptical core result in a very high birefringence of 1 × 10−3 and thus high initial Bragg peak spectral separation of 1.16 nm, as well as a very high transverse force sensitivity, of up to 650 pm/(N/mm) or even −1150 pm/(N/mm), depending on the fiber orientation with respect to the applied force. Due to the ~22 %m/m GeO2 concentration in the core the fiber being highly photosensitive, which significantly simplifies FBG fabrication by UV illumination without the need for prior hydrogen loading, which worsens thermal stability. Finally, the developed FBGs written in the highly birefringent side-hole elliptical core optical fiber were embedded in the square composite plates and applied for strain measurements. Tests of two-directional four-point bending have shown usability of such FBG for two-axial in-plane strain measurement with a single FBG in iso-thermal conditions.

27 July 2024 in Measurement
Verified
Journal Article
Open access
KWKarol Wachtarczyk
Karol Wachtarczyk
NYNeha Yadav
Neha Yadav
ABAleksander Błachut
Aleksander Błachut
PGPawel Gasior
Pawel Gasior
RSRalf Schledjewski
Ralf Schledjewski
JKJerzy Kaleta
Jerzy Kaleta

19 September 2022 in Materials
Verified
Journal Article
Open access
PDF file
KWKarol Wachtarczyk
Karol Wachtarczyk
MBMarcel Bender
Marcel Bender
EFEwald Fauster
Ewald Fauster
Ralf SchledjewskiRalf Schledjewski
Ralf Schledjewski
PGPawel Gasior
Pawel Gasior
JKJerzy Kaleta
Jerzy Kaleta
Material as well as process variations in the composites industry are reasons to develop methods for in-line monitoring, which would increase reproducibility of the manufacturing process and the final composite products. Fiber Bragg Gratings (FBGs) have shown to be useful for monitoring liquid-composite molding processes, e.g., in terms of online gel point detection. Existing works however, focus on in-plane strain measurements while out-of-plane residual strain prevails. In order to measure out-of-plane strain, FBG inscribed in highly birefringent fiber (HB FBG) can be used. The purpose of this research is the cure stage detection with (a) FBG inscribed in single mode and (b) FBG inscribed in highly-birefringent side-hole fiber in comparison to the reference gel point detected with an in-mold DC sensor. Results reveal that the curing process is better traceable with HB FBG than with regular FBG. Thus, the use of HB FBG can be a good method for the gel point estimation in the RTM process.

2 October 2017 in Journal of Science of the Gen. Tadeusz Kosciuszko Military Academy of Land Forces
Verified
Journal Article
Closed access
PKPiotr Krysiak
Piotr Krysiak
JKJerzy Kaleta
Jerzy Kaleta
PGPawel Gasior
Pawel Gasior
ABAleksander Błachut
Aleksander Błachut
RRRadosław RYBCZYŃSKI
Radosław RYBCZYŃSKI
The paper presents the measurements and the analysis of deformations between lay-ers and the outside surface of a multilayer filament wound composite pipe. The pipe was made through the hoop wrap of roving stripes hence ring-shaped samples were prepared for test purposes. Carbon fibers and glass fibers were used for winding. In the course of their manufacturing, strain gauges and fiber optic sensors were placed be-tween the composite layers. Then, the strength tests were performed. The samples were subjected to the internal pressure of 30 MPa. During the tests peripheral defor-mations were measured on outside surfaces of individual layers of the structure.

25 March 2010
Verified
Conference Paper
Closed access
PGPawel Gasior
Pawel Gasior
JKJerzy Kaleta
Jerzy Kaleta
APAleksander Przygoda
Aleksander Przygoda
This work presents application of SHM system based on optical fiber sensors for a power boiler monitoring. The test object was a modern fluid boiler made by RAFAKO SA. Because of the need to replace the pre-heaters it was necessary to make sure that such refurbishment would not menace the safety of the whole construction. Possible dangers could arise from the fact that additional openings in the main combustion chamber walls were made. For this purpose an SHM system based on SOFO® sensors was applied. The main task of the system was to locally measure a deformation of the construction, to give information about emerging threats as well as to start programmed alarms. The data obtained were continually published on the secured website. The arrangement of the sensors was supported by FEM analysis of the whole construction made by boiler producer. The sensors were installed on 12 strings of the combustion chamber. Additional 12 sensors were located directly on the chamber walls. Applied sensors were used to measure the deformation values in selected points. Then determined strain/stresses were compared with the design as well as with calculated values. It enabled evaluation of the inhomogeneous loads distribution and increased safety of the construction during its repair.