Daewon Kim

Dr. Daewon Kim

Department of Aerospace Engineering, Embry-Riddle Aeronautical University, Daytona Beach, FL, USA
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
22 June 2021 in Actuators
Verified
Journal Article
Open access
PDF file
SSStanislav Sikulskyi
Stanislav Sikulskyi
DMDanayit T. Mekonnen
Danayit T. Mekonnen
AAAbdullah El Atrache
Abdullah El Atrache
EDEduardo Divo
Eduardo Divo
Daewon KimDaewon Kim
Daewon Kim
Integrating nano- to micro-sized dielectric fillers to elastomer matrices to form dielectric composites is one of the commonly utilized methods to improve the performance of dielectric elastomer actuators (DEAs). Barium titanate (BaTiO3) is among the widely used ferroelectric fillers for this purpose; however, calcium copper titanate CaCu3Ti4O12 (CCTO) has the potential to outperform such conventional fillers. Despite their promising performance, CCTO-based dielectric composites for DEA application are studied to a relatively lower degree. Particularly, the composites are characterized for a comparably small particle loading range, while critical DEA properties such as breakdown strength and nonlinear elasticity are barely addressed in the literature. Thus, in this study, CCTO was paired with polydimethylsiloxane (CH3)3SiO[Si(CH3)2O]nSi(CH3)3 (PDMS), Sylgard 184, to gain a comprehensive understanding of the effects of particle loading and size on the dielectric composite properties important for DEA applications. The dielectric composites’ performance was described through the figures of merit (FOMs) that consider materials’ Young’s modulus, dielectric permittivity, and breakdown strength. The optimum amounts of the ferroelectric filler were determined through the FOMs to maximize composite DEA performance. Lastly, electromechanical testing of the pre-stretched CCTO-composite DEA validated the improved performance over the plain elastomer DEA, with deviations from prediction attributed to the studied composites’ nonlinearity.

17 December 2021 in Crystals
Verified
Journal Article
Open access
PDF file
RGRishikesh Srinivasaraghavan Govindarajan
Rishikesh Srinivasaraghavan Govindarajan
EREduardo Rojas-Nastrucci
Eduardo Rojas-Nastrucci
Daewon KimDaewon Kim
Daewon Kim
A surface acoustic wave (SAW), device composed of polymer and ceramic fillers, exhibiting high piezoelectricity and flexibility, has a wide range of sensing applications in the aerospace field. The demand for flexible SAW sensors has been gradually increasing due to their small size, wireless capability, low fabrication cost, and fast response time. This paper discusses the structural, thermal, and electrical properties of the developed sensor, based on different micro- and nano-fillers, such as lead zirconate titanate (PZT), calcium copper titanate (CCTO), and carbon nanotubes (CNTs), along with polyvinylidene fluoride (PVDF) as a polymer matrix. The piezocomposite substrate of the SAW sensor is fabricated using a hot press, while interdigital transducers (IDTs) are deposited through 3D printing. The piezoelectric properties are also enhanced using a non-contact corona poling technique under a high electric field to align the dipoles. Results show that the developed passive strain sensor can measure mechanical strains by examining the frequency shifts of the detected wave signals.

10 November 2023 in Polymers
Verified
Journal Article
Open access
PDF file
RGRishikesh Srinivasaraghavan Govindarajan
Rishikesh Srinivasaraghavan Govindarajan
SSStanislav Sikulskyi
Stanislav Sikulskyi
ZRZefu Ren
Zefu Ren
TSTaylor Stark
Taylor Stark
Daewon KimDaewon Kim
Daewon Kim
Recent developments in micro-scale additive manufacturing (AM) have opened new possibilities in state-of-the-art areas, including microelectromechanical systems (MEMS) with intrinsically soft and compliant components. While fabrication with soft materials further complicates micro-scale AM, a soft photocurable polydimethylsiloxane (PDMS) resin, IP-PDMS, has recently entered the market of two-photon polymerization (2PP) AM. To facilitate the development of microdevices with soft components through the application of 2PP technique and IP-PDMS material, this research paper presents a comprehensive material characterization of IP-PDMS. The significance of this study lies in the scarcity of existing research on this material and the thorough investigation of its properties, many of which are reported here for the first time. Particularly, for uncured IP-PDMS resin, this work evaluates a surface tension of 26.7 ± 4.2 mN/m, a contact angle with glass of 11.5 ± 0.6°, spin-coating behavior, a transmittance of more than 90% above 440 nm wavelength, and FTIR with all the properties reported for the first time. For cured IP-PDMS, novel characterizations include a small mechanical creep, a velocity-dependent friction coefficient with glass, a typical dielectric permittivity value of 2.63 ± 0.02, a high dielectric/breakdown strength for 3D-printed elastomers of up to 73.3 ± 13.3 V/µm and typical values for a spin coated elastomer of 85.7 ± 12.4 V/µm, while the measured contact angle with water of 103.7 ± 0.5°, Young’s modulus of 5.96 ± 0.2 MPa, and viscoelastic DMA mechanical characterization are compared with the previously reported values. Friction, permittivity, contact angle with water, and some of the breakdown strength measurements were performed with spin-coated cured IP-PDMS samples. Based on the performed characterization, IP-PDMS shows itself to be a promising material for micro-scale soft MEMS, including microfluidics, storage devices, and micro-scale smart material technologies.

1 December 2025 in Actuators
Verified
Journal Article
Open access
PDF file
AZAliya Zhagiparova
Aliya Zhagiparova
Vladimir V. GolubevVladimir V. Golubev
Vladimir V. Golubev
Daewon KimDaewon Kim
Daewon Kim
Pneumatic Artificial Muscles (PAMs) are soft actuators that mimic the contractile behavior of biological muscles through fluid-driven deformation. Originating from McKibben’s 1950s braided design, PAMs have evolved into a diverse class of actuators, offering high power-to-weight ratios, compliance, and safe human interaction, with applications spanning rehabilitation, assistive robotics, aerospace, and adaptive structures. This review surveys recent developments in actuation mechanisms and applications of PAMs. Traditional designs, including braided, pleated, netted, and embedded types, remain widely used but face challenges such as hysteresis, limited contraction, and nonlinear control. To address these limitations, researchers have introduced non-traditional mechanisms such as vacuum-powered, inverse, foldable, origami-based, reconfigurable, and hybrid PAMs. These innovations improve the contraction range, efficiency, control precision, and integration into compact or untethered systems. This review also highlights applications beyond conventional biomechanics and automation, including embodied computation, deployable aerospace systems, and adaptive architecture. Collectively, these advances demonstrate PAMs’ expanding role as versatile soft actuators. Ongoing research is expected to refine material durability, control strategies, and multifunctionality, enabling the next generation of wearable devices, soft robots, and energy-efficient adaptive systems.

16 December 2022 in Frontiers in Robotics and AI
Verified
Journal Article
Open access
SSStanislav Sikulskyi
Stanislav Sikulskyi
ZRZefu Ren
Zefu Ren
DMDanayit T. Mekonnen
Danayit T. Mekonnen
AHAleiya Holyoak
Aleiya Holyoak
RGRishikesh Srinivasaraghavan Govindarajan
Rishikesh Srinivasaraghavan Govindarajan
Daewon KimDaewon Kim
Daewon Kim
Dielectric elastomer actuator (DEA) is a smart material that holds promise for soft robotics due to the material’s intrinsic softness, high energy density, fast response, and reversible electromechanical characteristics. Like for most soft robotics materials, additive manufacturing (AM) can significantly benefit DEAs and is mainly applied to the unimorph DEA (UDEA) configuration. While major aspects of UDEA modeling are known, 3D printed UDEAs are subject to specific material and geometrical limitations due to the AM process and require a more thorough analysis of their design and performance. Furthermore, a figure of merit (FOM) is an analytical tool that is frequently used for planar DEA design optimization and material selection but is not yet derived for UDEA. Thus, the objective of the paper is modeling of 3D printed UDEAs, analyzing the effects of their design features on the actuation performance, and deriving FOMs for UDEAs. As a result, the derived analytical model demonstrates dependence of actuation performance on various design parameters typical for 3D printed DEAs, provides a new optimum thickness to Young’s modulus ratio of UDEA layers when designing a 3D printed DEA with fixed dielectric elastomer layer thickness, and serves as a base for UDEAs’ FOMs. The FOMs have various degrees of complexity depending on considered UDEA design features. The model was numerically verified and experimentally validated through the actuation of a 3D printed UDEA. The fabricated and tested UDEA design was optimized geometrically by controlling the thickness of each layer and from the material perspective by mixing commercially available silicones in non-standard ratios for the passive and dielectric layers. Finally, the prepared non-standard mix ratios of the silicones were characterized for their viscosity dynamics during curing at various conditions to investigate the silicones’ manufacturability through AM.

21 July 2020 in Smart Materials and Structures
Verified
Journal Article
Closed access
AGAudrey Gbaguidi
Audrey Gbaguidi
FMForam Madiyar
Foram Madiyar
Daewon KimDaewon Kim
Daewon Kim
SNSirish Namilae
Sirish Namilae
The sensitivity of the electronic properties of carbon nanotubes to gases, chemicals, temperature, and mechanical strain enables their use as fillers in nanocomposites for sensing applications. In this paper, the authors develop a low-cost and scalable process based on inkjet printing technology to fabricate printed flexible sensors used for strain and damage detection. A well-dispersed conductive water-based ink is fabricated with functionalized multiwall carbon nanotubes (MWCNT) and deposited onto paper and Kapton substrates to obtain a sheet resistance as low as 500 Ω sq −1 with about 30 printed layers. The number of printed layers, the direction of the electrical resistance measurement, and the type of substrate have clear effects on the sensor’s electrical performances related to the detection of mechanical strain and impact damage. This work demonstrates the effectiveness of the printed sensors for micrometeoroid and orbital debris (MMOD) impact damage detection through hypervelocity testing.