Andrii Hrubiak

Mr. Andrii Hrubiak

Doctor student
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 June 2023 in Energies
Verified
Journal Article
Open access
PDF file
Lina KieushLina Kieush
Lina Kieush
JSJohannes Schenk
Johannes Schenk
Andrii KoveriaAndrii Koveria
Andrii Koveria
AHAndrii Hrubiak
Andrii Hrubiak
HHHorst Hopfinger
Horst Hopfinger
HZHeng Zheng
Heng Zheng
The influence of different carbon sources, including anthracite, calcined petroleum coke, three samples of high-temperature coke, biochar, and a mixture of 50 wt.% biochar and 50 wt.% coke, on slag foaming behavior was studied. The slag’s composition was set to FeO-CaO-Al2O3-MgO-SiO2, and the temperature for slag foaming was 1600 °C. The effect of the carbon sources was evaluated using foaming characteristics (foam height, foam volume, relative foaming height, and gas fraction), X-ray diffraction (XRD), chemical analysis of the slag foams, Mossbauer spectroscopy, observation by scanning electron microscope (SEM), and energy-dispersive spectroscopy (EDS) mapping. Different foaming phenomena were found among conventional sources, biochar as a single source, and the mixture of coke and biochar. Biochar showed the most inferior foaming characteristics compared to the other studied carbon sources. Nevertheless, the slag foaming process was improved and showed slag foaming characteristics similar to results obtained using conventional carbon sources when the mixture of 50 wt.% coke and 50 wt.% biochar was used. The XRD analysis revealed a difference between the top and bottom of the slag foams. In almost all cases, a maghemite crystalline phase was detected at the top of the slag foams, indicating oxidation; metallic iron was found at the bottom. Furthermore, a difference in the slag foam (mixture of coke and biochar) was found in the presence of such crystalline phases as magnesium iron oxide (Fe2MgO4) and magnetite (Mg0.4Fe2.96O4). Notwithstanding the carbon source applied, a layer between the foam slag and the crucible wall was found in many samples. Based on the SEM/EDS and XRD results, it was assumed this layer consists of gehlenite (Ca2(Al(AlSi)O7) and two spinels: magnesium aluminate (MgAl2O4) and magnesium iron oxide (Fe2MgO4).

6 April 2023 in Metals
Verified
Journal Article
Open access
PDF file
Lina KieushLina Kieush
Lina Kieush
JSJohannes Schenk
Johannes Schenk
Andrii KoveriaAndrii Koveria
Andrii Koveria
GRGerd Rantitsch
Gerd Rantitsch
AHAndrii Hrubiak
Andrii Hrubiak
HHHorst Hopfinger
Horst Hopfinger
Conventional (anthracite, calcined petroleum coke, and coke) and non-conventional (biochar, and biocokes (3 wt.% torrefied wood, and 3 wt.% petroleum coke + 3 wt.% charcoal)) carbon-bearing sources have been studied for their use in electric arc furnace (EAF)-based steel production. Commonly, for the use of carbon sources in EAFs, one of the important properties is the content of fixed carbon, the release of volatiles as well as the elemental composition of inorganics. The properties of six carbon sources were analyzed by determining the proximate analysis, X-ray fluorescence analysis (XRF), coke reactivity index (CRI), and strength after reaction with CO2 (CSR), Brunauer–Emmett–Teller (BET) specific surface area and Barrett–Joyner–Halenda (BJH) pore size and volume analysis, ash chemical analysis, optical and scanning microscopy, Raman spectroscopy and X-ray diffraction (XRD) analysis. The results indicate biocoke as a promising option to replace conventional carbon-bearing sources. In the sample set, the fixed carbon, volatiles, and ash content of the biocokes were similar despite the total difference in additives. Additionally, the use of additives did not significantly affect the biocoke reactivity indices, but slightly decreased the strength after the reaction with CO2. Carbon-bearing sources have been characterized in terms of their structural properties. XRD analysis revealed that the amount of disordered carbon increased in the order: coke < calcined petroleum coke ~ biocoke (3 wt.% torrefied wood) < biocoke (3 wt.% petroleum coke + 3 wt.% charcoal) < biochar. The results obtained on the physical, chemical, and structural properties of carbon sources are the basis for further research on the behavior of slag foaming.

30 June 2022 in Mining of Mineral Deposits
Verified
Journal Article
Open access
Lina KieushLina Kieush
Lina Kieush
Andrii KoveriaAndrii Koveria
Andrii Koveria
MBMaksym Boyko
Maksym Boyko
MYMaksym Yaholnyk
Maksym Yaholnyk
AHAndrii Hrubiak
Andrii Hrubiak
VMVolodymyr Moklyak
Volodymyr Moklyak
Purpose. The research purpose is to substantiate the use of biocoke as a fuel in the iron ore sintering, as well as its influence on the performance and properties of the resulting sinter. To completely replace conventional coke breeze, biocoke is produced using 5 wt.% biomass wood pellets at different carbonization temperatures of 950 or 1100°C. Further, the influence of biocoke on the sintering process and the sinter quality is studied at a high proportion of biomass pellets of 10, 15, 30, 45 wt.% and a carbonization temperature of 950°C. Methods. Carbonization is performed in shaft-type electric furnaces to produce laboratory coke or biocoke. Afterward, the sintering of iron ores is conducted on a sinter plant. To assess the sintering process and the quality of the resulting sinter, the filtration rate is determined on a laboratory sinter plant using a vane anemometer designed to measure the directional flow average velocity under industrial conditions. The sinter reducibility is studied using a vertical heating furnace to assess the effect of coke and biocoke on the sinter’s physical-chemical properties. Findings. It has been determined that biocoke, carbonized at a temperature of 950°C, has good prospects and potential for a shift to a sustainable process of iron ore sintering. Originality. It has been proven that biocoke with a biomass pellet ratio of up to 15 wt.%, obtained at a temperature of 950°C, does not affect the parameters characterizing the sintering process. The sinter strength indicators correspond to the use of 100 wt.% conventional coke breeze. Biocoke used with a high proportion of biomass pellets of 30 and 45 wt.% causes a deterioration in the sinter quality. Practical implications. The results of using biocoke with the addition of 5-15 wt.% biomass pellets and at a temperature of 950°C are within the standard deviation, which makes it possible to use biocoke with 15 wt.% biomass pellets instead of industrial coke breeze.

18 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
Oleg BazalukOleg Bazaluk
Oleg Bazaluk
AHAndrii Hrubiak
Andrii Hrubiak
VMVolodymyr Moklyak
Volodymyr Moklyak
MMMaria Moklyak
Maria Moklyak
Lina KieushLina Kieush
Lina Kieush
SFSerhii Fedorov
Serhii Fedorov
The paper presents a method for obtaining electrochemically active ultrafine composites of iron oxides, superparamagnetic ‘core/shell’ γ-Fe2O3/defective α-Fe2O3, which involved modifying sol-gel citrate synthesis, hydrothermal treatment of the formed sol, and subsequent annealing of materials in the air. The synthesized materials’ phase composition, magnetic microstructure, and structural, morphological characteristics have been determined via X-ray analysis, Mossbauer spectroscopy, scanning electron microscopy (SEM), and adsorption porometry. The mechanisms of phase stability were analyzed, and the model was suggested as FeOOH → γ-Fe2O3 → α-Fe2O3. It was found that the presence of chelating agents in hydrothermal synthesis encapsulated the nucleus of the new phase in the reactor and interfered with the direct processes of recrystallization of the structure with the subsequent formation of the α-Fe2O3 crystalline phase. Additionally, the conductive properties of the synthesized materials were determined by impedance spectroscopy. The electrochemical activity of the synthesized materials was evaluated by the method of cyclic voltammetry using a three-electrode cell in a 3.5 M aqueous solution of KOH. For the ultrafine superparamagnetic ‘core/shell’ γ-Fe2O3/defective α-Fe2O composite with defective hematite structure and the presence of ultra-dispersed maghemite with particles in the superparamagnetic state was fixed increased electrochemical activity, and specific discharge capacity of the material is 177 F/g with a Coulomb efficiency of 85%. The prototypes of hybrid supercapacitor with work electrodes based on ultrafine composites superparamagnetic ‘core/shell’ γ-Fe2O3/defective α-Fe2O3 have a specific discharge capacity of 124 F/g with a Coulomb efficiency of 93% for current 10 mA.

5 February 2024 in Journal of Sustainable Metallurgy
Verified
Journal Article
Closed access
PDF file
Lina KieushLina Kieush
Lina Kieush
JSJohannes Schenk
Johannes Schenk
Andrii KoveriaAndrii Koveria
Andrii Koveria
AHAndrii Hrubiak
Andrii Hrubiak

20 July 2021 in Batteries
Verified
Journal Article
Open access
PDF file
VMVolodymyr Moklyak
Volodymyr Moklyak
AHAndrii Hrubiak
Andrii Hrubiak
ZGZurab Gogitidze
Zurab Gogitidze
YYYurii Yavorskyi
Yurii Yavorskyi
The work shows a new approach to improving the performance of lithium power sources by using polypeptides as an active component of the cathode composition. Specifically, the experimental results of testing prototypes of lithium current sources with cathodes based on polypeptides, which demonstrate the value of the specific discharge capacity at the level of 2000–2700 mAh/g, depending on the content of the organic component, are presented. The use of the intermittent galvanostatic titration mode during the discharge showed an increase in the specific indicators of the current sources in comparison with the continuous discharge at different specific load currents. Based on this, the effect of “relaxation recovery” of the cathode material based on polypeptides was discovered, the essence of which is a significant increase (recovery) of the open-circuit voltage when the load of the lithium current source is disconnected, which leads to an increase of the discharge capacity without external energy influences. The functionalization of the surface of thermally expanded graphite with polypeptide components made it possible to create a cathode material, the use of which in lithium current source models increased the specific discharge capacity to 19,000 mA h/g at a discharge current of 10 mA/h.