The specific heat at constant pressure C(T) of bundles of single-walled carbon nanotubes (SWNTs) closed at their ends has been investigated in the temperature interval of 2–120 K. It is found that the curve C(T) has features near 5, 36, 80, and 100 K. The experimental results on the C(T) and the radial thermal expansion coefficient αR(T) of bundles of SWNTs oriented perpendicular to the sample axis have been compared. It is found that the curves C(T) and αR(T) exhibit a similar temperature behavior at T > 10 K. The temperature dependence of the Grüneisen coefficient γ(T) has been calculated. The curve γ(T) also has a feature near 36 K. Above 36 K the Grüneisen coefficient is practically independent of temperature (γ ≈ 4). Below 36 K, γ(T) decreases monotonically with lowering temperature and becomes negative at T < 6 K.
The Vickers hardness and Young’s modulus of the hydroxyapatite (HA) bioceramics with a small amount of the multi-walled carbon nanotubes (MWCNTs) were studied by using ultramicrotester Shimadzu for dynamic tests DUH-211. Small concentrations of MWCNTs were from 0.05 to 0.5 wt.%. The argon inert atmosphere and vacuum condition were taken for the prevention of the MWCNTs oxidation. The Brunauer–Emmett–Teller (BET) surface area SBET of the HA-MWCNTs composites was determined by thermal adsorption-desorption of nitrogen. It was found that for HA-MWCNTs sintered in the Ar atmosphere, an increase in the concentration of nanotubes up to 0.5 wt.% leads to a decrease in porosity near 3 times in comparison to HA without MWCNTs additives. The small amount of additives of multi-walled carbon nanotubes leads to an increase in hardness of 1.3 times and compression strength of composite and compression strength of composite that is comparable in absolute values with the literature data of enamel hardness (3–5 GPa) and compression strength (95–370 MPa). The absolute values increase close to linearly with the increase of nanotube concentrations. The Young’s modulus of sintered composite slightly changes with the variation of concentrations of nanotubes and close to the enamel (75–100 GPa). The ratio of plastic work to total work and the ratio of elastic (reversible) work to the total work of deformation of composite HA/MWCNTs are practically constant at a studied range of MWCNTs concentration. The additives of the multi-walled carbon nanotubes lead to both an increase in the elasticity index of ~1.5 times and an increase in the resistance to plastic deformation of ~3 times, which improved the tribological performance of the surface. Plastic and elastic (reversible) work slightly changed.
The heat capacity of bundles of closed-cap single-walled carbon nanotubes with one-dimensional chains of nitrogen molecules adsorbed in the grooves has been first experimentally studied at temperatures from 2 to 40 K using an adiabatic calorimeter. The contribution of nitrogen CN2 to the total heat capacity has been separated. In the region 2–8 K the behavior of the curve CN2(T) is qualitatively similar to the theoretical prediction of the phonon heat capacity of 1D chains of Kr atoms localized in the grooves of SWNT bundles. Below 3 K the dependence CN2(T) is linear. Above 8 K the dependence CN2(T) becomes steeper in comparison with the case of Kr atoms. This behavior of the heat capacity CN2(T) is due to the contribution of the rotational degrees of freedom of the N2 molecules.
11 September 2020 in Fullerenes, Nanotubes and Carbon Nanostructures
DSC and calorimetric studies of multi-walled carbon nanotubes (MWCNTs) with average diameters in the range 7, 9 and 18 nm were carried out. MWCNTs were obtained by the CVD method. The kinetic processes in MWCNTs were studied from room temperature to 550 °C in a nitrogen flow using differential scanning calorimetry (DSC) on a Perkin – Elmer — 8000. It was found that exo- and endothermic peaks are not observed on the DSC curves after water evaporation. This indicates that all studied MWCNTs have a small number of defects, functional groups, and other impurities. The heat capacity of MWCNTs was measured by the relaxation method in the temperature range from 2 to 275 K by using PPMS. In the temperature dependences of the specific heat were observed that for MWCNTs with the decrease of the temperature below 20 K the curves shift to lower values with an increase the average diameter. The main result was that at temperatures below 45 K with the decreasing of the nanotubes diameter the ratio of heat capacity of nanotubes to the heat capacity of graphite increases. The perfection of structure and low amount of the defects, functional groups and impurity contamination for MWCNTs were demonstrated in the comparison of the XPS and NEXAFS spectra for these nanotubes with CVD prepared nanotubes (18 nm) after mechanical and chemical functionalization.
The experimental studies of the heat capacity of 1D chains of xenon atoms adsorbed in the outer grooves of bundles of closed single-walled carbon nanotubes CXe have been first made at temperature range 2–30 K with the adiabatic calorimeter. The experimental data CXe have been compared with theory [A. Šiber, Phys. Rev. B 66, 235414 (2002)]. The experimental and theoretical heat capacity curves are close below 8 K. Above 8 K the experimental curve CXe(T) exceeds the theoretical one and excess capacity ΔCXe(T) increases monotonously with temperature. We assume that the ΔCXe(T) caused mainly by the increase of the distance between the neighboring xenon atoms in the chain with increasing temperature.