Oliver Löhmann

Dr. Oliver Löhmann

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2022 in Soft Matter
Verified
Journal Article
Open access
PDF file
MKMatthias Kühnhammer
Matthias Kühnhammer
KGKevin Gräff
Kevin Gräff
ELEdwin Loran
Edwin Loran
OSOlaf Soltwedel
Olaf Soltwedel
OLOliver Löhmann
Oliver Löhmann
RKRegine Von Klitzing
Regine Von Klitzing
PNIPAM microgels form inhomogeneous network-like structures with microgel depleted and microgel bearing zones when confined in foam films.

20 December 2019 in Chemical Communications
Verified
Journal Article
Open access
PDF file
MUMartin Uhlig
Martin Uhlig
OLOliver Löhmann
Oliver Löhmann
SRSalomé Vargas Ruiz
Salomé Vargas Ruiz
IVImre Varga
Imre Varga
RKRegine Von Klitzing
Regine Von Klitzing
RCRichard A Campbell
Richard A Campbell
The foam film stability of polyelectrolyte/surfactant mixtures is rationalized using structural data from neutron reflectometry for the first time.

29 April 2021 in Applied Sciences
Verified
Journal Article
Open access
PDF file
TWTobias Widmann
Tobias Widmann
LKLucas Kreuzer
Lucas Kreuzer
MKMatthias Kühnhammer
Matthias Kühnhammer
ASAndreas J. Schmid
Andreas J. Schmid
LWLars Wiehemeier
Lars Wiehemeier
Peter Muller-BuschbaumPeter Muller-Buschbaum
Peter Muller-Buschbaum
The FlexiProb project is a joint effort of three soft matter groups at the Universities of Bielefeld, Darmstadt, and Munich with scientific support from the European Spallation Source (ESS), the small-K advanced diffractometer (SKADI) beamline development group of the Jülich Centre for Neutron Science (JCNS), and the Heinz Maier-Leibnitz Zentrum (MLZ). Within this framework, a flexible and quickly interchangeable sample carrier system for small-angle neutron scattering (SANS) at the ESS was developed. In the present contribution, the development of a sample environment for the investigation of soft matter thin films with grazing-incidence small-angle neutron scattering (GISANS) is introduced. Therefore, components were assembled on an optical breadboard for the measurement of thin film samples under controlled ambient conditions, with adjustable temperature and humidity, as well as the optional in situ recording of the film thickness via spectral reflectance. Samples were placed in a 3D-printed spherical humidity metal chamber, which enabled the accurate control of experimental conditions via water-heated channels within its walls. A separately heated gas flow stream supplied an adjustable flow of dry or saturated solvent vapor. First test experiments proved the concept of the setup and respective component functionality.

31 May 2022 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
LBLarissa Braun
Larissa Braun
MUMartin Uhlig
Martin Uhlig
OLOliver Löhmann
Oliver Löhmann
RCRichard A Campbell
Richard A Campbell
ESEmanuel Schneck
Emanuel Schneck
RKRegine von Klitzing
Regine von Klitzing

16 November 2015 in Soft Matter
Verified
Journal Article
Closed access
PDF file
SMSamantha Micciulla
Samantha Micciulla
OSOlaf Soltwedel
Olaf Soltwedel
OLOliver Löhmann
Oliver Löhmann
RKRegine Von Klitzing
Regine Von Klitzing
The complex interaction of polyelectrolyte multilayers (PEMs) physisorbed onto end-grafted polymer brushes with focus on the temperature-responsive behavior of the system is addressed in this work. The investigated brush/multilayer composite consists of a poly(styrene sulfonate)/poly(diallyldimethylammonium chloride) (PSS/PDADMAC) multilayer deposited onto the poly(N-isopropylacrylamide-b-dimethylaminoethyl methacrylate) P(NIPAM-b-DMAEMA) brush. Ellipsometry and neutron reflectometry were used to monitor the brush collapse with the thickness decrease as a function of temperature and the change in the monomer distribution perpendicular to the substrate at temperatures below, across and above the phase transition, respectively. It was found that the adsorption of PEMs onto polymer brushes had a hydrophobization effect on PDMAEMA, inducing the shift of its phase transition to lower temperatures, but without suppressing its temperature-responsiveness. Moreover, the diffusion of the free polyelectrolyte chains inside the charged brush was proved by comparing the neutron scattering length density profile of pure and the corresponding PEM-capped brushes, eased by the enhanced contrast between hydrogenated brushes and deuterated PSS chains. The results presented herein demonstrate the possibility of combining a temperature-responsive brush with polyelectrolyte multilayers without quenching the responsive behavior, even though significant interpolyelectrolyte interactions are present. This is of importance for the design of multicompartment coatings, where the brush can be used as a reservoir for the controlled release of substances and the multilayer on the top as a membrane to control the diffusion in/out by applying different stimuli.

18 July 2018 in The Journal of Chemical Physics
Verified
Journal Article
Closed access
PDF file
DBDikran Boyaciyan
Dikran Boyaciyan
LBLarissa Braun
Larissa Braun
OLOliver Löhmann
Oliver Löhmann
LSLuca Silvi
Luca Silvi
ESEmanuel Schneck
Emanuel Schneck
RKRegine Von Klitzing
Regine Von Klitzing
Composites made of polymer brushes with inclusions of gold nanoparticles (AuNPs) combine the responsive nature of polymer brushes with the optical properties of the AuNPs, which offers the possibility to be used as colorimetric sensors. To this end, it is crucial to know how AuNPs are distributed inside the brush. Here, this distribution was elucidated by neutron reflectometry with contrast variation and a self-consistent reflectivity analysis based on the analytical parameterization of the volume fraction profiles of all chemical components. In contrast to former studies, this analysis allows the determination of the spatial distribution of components separately from each other: polyelectrolyte, AuNP, and water. Cationic poly-[2-(Methacryloyloxy) ethyl] trimethylammonium chloride (PMETAC) brushes were loaded with 5 nm AuNPs, which were coated with a pH-sensitive capping. The pH was varied during the incubation of the brush in the AuNP suspension. At a lower pH, AuNPs form aggregates in suspension and are attached to the brush periphery. They adsorb into the brush but do not fully penetrate it due to their bulkiness. At a higher pH, AuNP suspensions are electrostatically stabilized and the AuNPs penetrate the brush entirely. However, the AuNP distribution over the brush is not homogeneous but decreases gradually toward the substrate. Penetration of the AuNPs leads to a more extended conformation of the brush. According to the results of the detailed analysis of all components, an increase in water content could be excluded as a reason for brush swelling but replacement of water by the AuNP was observed.