The electric arc furnace (EAF) has the potential to significantly contribute to the decarbonization of the iron and steel industry. However, during EAF steelmaking, carbon still needs to be injected into the molten slag to initiate slag foaming, which is beneficial to the energy efficiency and protection of the furnace. To move away from fossil carbon, biocarbon has gained attention as an injection carbon agent. In this study, two biochar candidates were added to the molten slag layer of an induction furnace for steel melting, to simulate EAF steelmaking conditions. The resultant slag foaming height was measured, and a ranking in comparison to two fossil carbon candidates was developed. The results indicate that the injection biochar sample, in the form of a bio-briquette, has a considerable degree of slag foaming capacity. More work is ongoing to develop a standardized testing methodology of ranking various injection biochar candidates for their suitability and qualification for use on a larger scale.
30 September 2017 in European Journal of Wood and Wood Products
Electric arc furnaces (EAFs) are used for steel production, particularly when recycling scrap material. In EAFs, carbonaceous material is charged with other raw materials or injected into molten slag to generate foam on top of liquid metal to increase energy efficiency. However, the consumption of fossil carbon leads to greenhouse gas emissions (GHGs). To reduce net GHG emissions from EAF steelmaking, the substitution of fossil carbon with sustainable biogenic carbon can be applied. This study explores the possibility of the substitution of fossil material with biogenic material produced by different pyrolysis methods and from various raw materials in EAF steelmaking processes. Experimental work was performed to study the effect of biogenic material utilization on steel and slag composition using an induction melting furnace with 50 kg of steel capacity. The interaction of biogenic material derived from different raw materials and pyrolysis processes with molten synthetic slag was also investigated using a tensiometer. Relative to other biogenic materials tested, a composite produced with densified softwood had higher intensity interfacial reactions with slag, which may be attributed to the rougher surface morphology of the densified biogenic material.
16 February 2023 in International Journal of Coal Preparation and Utilization
Coal rheology is a critical parameter for determining the coking and caking ability of metallurgical coals for cokemaking. The effect of rank, hardness differences due to rank, and particle size on the resultant fluidity and dilatation results were demonstrated for various rank Applachian coals in previous studies. Particles less than USA Standard screen size No. 140 had poorer rheology responses compared to other size fractions. For the third phase of this study, the effect of particle size and rank of Western Canadian coals were also evaluated. All samples and rheology parameters were determined prepared using the standard ASTM methods. In addition, rheology was also measured on sized subsets to determine the effect of particle size and rank on the overall rheology results but from a different geological era compared to Applachian coals. Particle size limits for the Gieseler and Dilatometer tests are suggested. The importance of using temperature range is also emphasized.
19 April 2020 in International Journal of Coal Preparation and Utilization
Partial substitution of pulverized coal (PCI) by renewable biocarbon for blast furnace injection is a practical approach to reduce GHGs in the steel production sector. For using biocarbon as feedstock, it is critical to measure its grindability to understand its milling behavior compared to that of typical PCI coal, and thus help decide on adjusting grinding process of existing equipment or selecting appropriate milling equipment. From the significant differences in chemical and physical properties of biocarbon and PCI coal, grinding capacity variations are also expected. In addition, as the pyrolysis process modifies the chemical and physical properties of biomass, this could affect the efficiency of co-milling with coal and therefore co-injection in blast furnace ironmaking. The increase in milling capacity in turn would enable a reduction in the amount of coal used without the requirement for supplementary grinding facility. This paper presents an experimental investigation of the co-grinding behavior of coal and biocarbon produced by pyrolysis of woody biomass from two different conditions and post-processes. The main aim of this study was to identify or develop a method of grindability determination for coal, biocarbon blend, which would allow direct comparison between coal, biocarbon, and coal-biocarbon blends in terms of their grinding capacity. The study also includes the assessment of the possibility of adapting the existing coal and biomass grindability determination method for the evaluation of coalbiocarbon co-milling. The laboratory tests used focused on the influence of initial sample fixed mass and volume, composition of coal and biocarbon, the pyrolysis severity of biocarbon, and the densification process of biocarbon. The grinding behavior of biocarbon-coal mixtures determined by ASTM HGI procedure for coal is presented and compared in this paper. The findings show that milling tests conducted with fixed sample mass and fixed sample volume on same coal-biocarbon blend sample produce different and unrelated results. Moreover, grinding test results with fixed initial sample volume does not reflect material behavior in industrial grinding facilities. Therefore, it is suggested that the ASTM HGI method should be strictly followed to generate comparable grindability data for coal, biocarbon, and coal-biocarbon mixtures.