Renewable energy sources based on solar and wind energy provide clean and efficient energy. The intermittent behaviour of these sources is challenging. At the same time, the needs for efficient, continuous and clean energy sources are increased for serving both electricity and thermal demands for residential buildings. Consequently, complimentary systems are essential in order to ensure a continuous power generation. One of the promising energy sources that helps in reducing CO2 emissions, in addition to providing electrical and thermal energy efficiently, is a Solid Oxide Fuel Cell (SOFC) system operated in a combined heat and power (CHP) mode, due to high electrical efficiencies (in full and part load) and the fuel flexibility. Currently, most studies tend to focus on fuel cell model details with basic information about the building’s energy requirements. Nevertheless, a deep understanding of integrating fuel cell micro-CHP systems with renewable energy systems for the residential sector is required. Moreover, it is important to define an operating strategy for the system with a specific controlling method. This helps in evaluating the performance and the efficiency of the building energy system. In this study, an investigation of different configurations of a hybrid power system (HPS) was carried out. The intended aim of this investigation was to optimize a HPS with minimal CO2 emissions, serving the energy demands for a single-family house efficiently and continuously. As a result of this study, a photovoltaic (PV)/SOFC micro-CHP system has satisfied the intended goal, where the CO2 emissions are significantly reduced by 88.6% compared to conventional systems. The SOFC micro-CHP plant operated as a complimentary back-up generator that serves the energy demands during the absence of the solar energy. Integrating the Power to Gas (PtG) technology leads to a similar emission reduction, while the PtG plant provided a seasonal energy storage. The excess energy produced during summer by the PV system is stored in the fuel storage for a later use (during winter). This SOFC micro-CHP configuration is recommended from an energy and environmental perspective. In terms of feasibility, the costs of SOFC based micro-CHP systems are significantly higher than traditional technologies. However, further technology developments and the effect of economy of scale may cause a substantial drop in costs and the micro-CHP shall become economically competitive and available for residential users; thus, enabling a self-sufficient and efficient energy production on site.
Solid Oxide Fuel Cell (SOFC) technology is of high interest for stationary decentralized generation of electricity and heat in combined heat and power systems (CHP) for the residential sector. Application scenarios for SOFC systems in an electricity-regulated mode play an important role, especially in places where an electrical grid connection is not available or rather unstable. The advantages of SOFC systems are the high fuel flexibility and the high efficiencies also under partial load operation compared to other decentralized power generation technologies. Due to the long, energy-consuming system heat-up and the limited partial load capability, SOFC systems do not reach the performance of conventional power generation technologies. Furthermore, stack thermal cycling is associated with power degradation and should be minimized. In this paper, the improvement of these drawbacks are investigated for hotbox-based SOFC systems in the 1 kWel-class for residential applications. Since experimental investigations of the high-temperature systems are limited, modeling tools are established, enabling the visualization of internal system characteristics and providing the opportunity to simulate system operation in critical regions. To achieve this, a methodology for dynamic SOFC system modeling in a process engineering manner is developed based on the modeling language Modelica. A suitable approach is particularly important for modeling and simulation of the strong thermal interaction between the hot system components within the hotbox. The parametrized and validated models are used for the investigation of different dynamic effects, such as the system heat-up and the operation in low partial load points. A second reduced thermal system model aims for annual simulations of the SOFC system together with a battery to investigate the number of thermal cycles and the advantage of a hot standby operation. As a result, it is found that an adequate control of the power input at the start-up device and the cathode air flow has a high improvement potential to increase the stack heating rate and accelerate the heat-up in an energy-saving way. The hotbox-internal thermal management is identified as a crucial issue to reach low partial load points. To avoid the risk of stack cooling, lower heat losses and/or additional heat sources are of importance. Furthermore, the robustness of the tail gas oxidizer is found to be crucial for a higher load flexibility during partial load and the end of life stack operation. The annual simulation results indicate that operating the battery hybrid system with a hot standby mode requires much lower battery capacity for a high grid independence and a complete avoidance of system shutdown and associated power degradation.
The sodium/nickel chloride battery (Na/NiCl2) is considered an eco-friendly, long-term stable and safe alternative to other secondary battery technologies. The overall system efficiency of this high-temperature battery can be increased by optimizing the thermal management system. This paper addresses the integration of a phase change material (PCM) into the battery modules and evaluates the thermal performance and environmental impact of such a design. The module layout with PCM and heat transfer elements (HTEs) was selected based on 2D FEM simulation results and verified in a prototype Na/NiCl2 module. It was shown that the module temperatures could be kept within the operating limits during operation by the HTEs and the PCM even at high current rates. Since no critical temperature limits were reached, the usable battery capacity was higher compared to results of a reference module without PCM or HTEs. In addition, the PCM prolonged the cooling down process after discharge. In parallel with the experimental studies, the environmental performance of the battery was evaluated using a life cycle assessment (LCA). Amongst other things, it was found that the application of PCM is also beneficial from an ecological point of view.
1 September 2022 in Journal of the Electrochemical Society
A pulsed discharge regime (GITT) was used to investigate the ohmic internal resistance of Na/NiCl2 cells, also known as ZEBRA Cells. Two ways were chosen to determine the internal resistance, on the one side the voltage response of the corresponding current enables a calculation. On the other side the potentiostatic electrochemical impedance spectroscopy (EIS) was used to measure cell spectra including the ohmic internal resistance. By comparing both methods the feasibility of ohmic internal resistance (IR) calculation can be evaluated. The cells were investigated within five different operating temperatures (300 °C–180 °C with 30 K steps). Results show that the ohmic internal resistance of a Na/NiCl2 is increasing when the operating temperature is decreasing, mainly due to the decrease of ionic conductivity of separator and the secondary electrolyte NaAlCl4. As a direct consequence, there is a significant capacity loss. Therefore, the operating temperature can be identified as capacity limiting factor.
Battery models are mathematical systems that aim to simulate real battery cell sufficiently accurately. Finding a comprise between complexity, computational effort and accuracy is thereby key. In particular, modelling sodium–nickel–chloride/iron-chloride cells (Na-), as a promising alternative for stationary energy storage, bears some challenges. The literature shows a few interesting approaches, but in most of them the second active material ( or ) or the entire discharging/charging cycle is not considered. In this work, an electrochemical and thermal model of Na- battery cells is presented. Based on an equivalent circuit approach combined with electrochemical calculations, the hybrid model provides information on the performance of the cell for charging and discharging with a constant current. By dividing the cathode space into segments, internal material and charge flows are predicted, allowing important insights into the internal cell processes. Besides a low calculation effort, the model also allows a flexible adaption of cathode composition and cell design, which makes it a promising tool for the development of single battery cells as well as battery modules and battery systems.
Today, off-grid communities rely mainly on diesel gensets with limited electrical efficiency and diesel furnaces for electricity and heat generation, respectively. The CO2 emissions associated with this electricity production can be reduced by improving the electrical efficiency of the system thus reducing the fuel consumption. Additionally, waste heat from the electricity production can be recovered for heating thus creating a combined heat and power system. In this work, a solid oxide fuel cell combined heat and power system hybridized to a battery was proposed for this purpose. Simulation of the annual electricity and heat production were performed using real temporal electrical demand data. Results showed that a reduction of up to 36 % in primary energy consumption can be reached compared with the current situation.