The pin-fin is one of the main technologies in enhancing heat transfer. The accelerated flow and vortex structures are produced, which can disrupt the development of the flow boundary layer. The configuration of the pin-fin is obvious for heat transfer and flow characteristics, including its shape, size, and arrangement in the cooling channel. This work provides a detailed introduction to the application of pin-fins in enhancing heat transfer and reducing flow resistance, including the conventional shapes, improved shapes based on circular pin-fins and irregular shapes. At the same time, the influence of the diameter, height and density of pin-fins on heat transfer and flow performance is studied, and the influence mechanism is analyzed from the perspective of boundary layers. In addition, some applications that combine pin-fins with other cooling methods to further improve performance are analyzed. In terms of the optimization technology, the structure optimization for pin-fin shape and the layout optimization for pin-fin array are summarized. Therefore, this review provides a wide range of literature for the design of internal cooling channel pin-fins.
In order to achieve uniform and effective impingement cooling, a swirling jet with a swirling angle of 45° (SIJ 45°) is put forward in this paper. Namely, there are four 45° spiral grooves equipped on the inner wall of the circular hole. The difference in the flow field and heat transfer characteristics between the conventional impinging jet (CIJ) and SIJ is compared and analyzed. The spiral channels can increase the heat transfer rate and cooling uniformity because of the action of superimposed airflow. In addition, the thread nozzle brings lower pressure loss, which can reduce the airflow friction while effectively ensuring high heat transfer in the center area of the jet. An experimental system is built to investigate the heat transfer and flow characteristics of the impingement surface. Smoke flow visualization technology is used to explore the complex flow field of the CIJ and SIJ , and the heat transfer rate of the target surface is analyzed based on thermocouple data. When and , the averaged Nusselt number (Nu) correlation for SIJ 45° is established, which is in good agreement with the experimental results. SIJ 45° is an effective measure to replace the CIJ, and the research herein provides some reference for designing the structure of new jets.
This research presents a surrogate model and computational fluid dynamic analysis-based multi-objective optimization approach for microchannel heat sinks. The Non-dominated Sorting Genetic Algorithm is suggested to obtain the optimal solution set, and the Kriging model is employed to lower the simulation’s computational cost. The physical model consists of a coolant chamber, a mainstream chamber, and a solid board equipped with staggered Zigzag cooling channels. Five design variables are examined in relation to the geometric characteristics of the microchannel heat sinks: the length of inlet of the cooling channels, the width of the cooling channels, the length of the “zigzag”, the height of the cooling channels, and the periodic spanwise width. The optimal geometry is established by choosing the averaged cooling effectiveness and coolant mass flow rate which enters the mainstream chamber through the microchannel heat sinks as separate objectives. From the Pareto front, the optimal microchannel heat sinks structures are obtained. Three optimized results are studied, including the maximum cooling effectiveness, minimum coolant mass flow rate, and a compromise between the both objectives; a reference case using the median is compared as well. Numerical assessments corresponding to the four cases are performed, and the flow and cooling performance are compared. Furthermore, an analysis is conducted on the mechanisms that impact the ideal geometric parameters for cooling performance.
In this investigation, the heat transfer and flow capabilities of an X-shaped truss array cooling channel under various operating conditions of gas turbine blades were thoroughly studied. The influence laws of the inlet Reynolds number, inlet turbulence intensity, wall heat flux and cooling medium (air, steam) on the heat transfer and flow performance of the X-shaped truss array channel were analyzed and summarized. The empirical correlations of friction coefficients and average Nusselt numbers with maximum deviations less than ± 14% were fitted. The results show that the inlet Reynolds number has the most significant effect on the flow and heat transfer performance of the X-shaped truss array channel. When the inlet Reynolds number increases from 20,000 to 200,000, the average Nusselt number of the X-shaped truss array channel is increased by 3.92 times, the friction coefficient is decreased by 12.88%, and the comprehensive thermal coefficient is decreased by 31.19%. Compared with the medium turbulence intensity of Tu = 5%, the average Nusselt number, friction coefficient and comprehensive thermal coefficient of the X-shaped truss array channel at Tu = 20% are increased by 3.70%, 2.51% and 2.79%, respectively. With the increase in the wall heat flux, the friction coefficient of the X-shaped truss array channel roughly shows a trend of first decreasing and then increasing, while the average Nusselt number and the comprehensive thermal coefficient show a trend of first rapidly increasing and then slightly decreasing or remaining unchanged. Compared with air cooling, the average Nusselt numbers of the X-shaped truss array channel of steam cooling are increased by 6.30% to 9.54%, and the corresponding friction coefficients and comprehensive thermal coefficients are decreased by 0.11% to 0.55% and 2.63% to 5.59%, respectively.