Zhen Zhao

Dr. Zhen Zhao

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 February 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
Lei XiLei Xi
Lei Xi
JGJianmin Gao
Jianmin Gao
XLXU Liang
XU Liang
Zhen ZhaoZhen Zhao
Zhen Zhao
QRQicheng Ruan
Qicheng Ruan
YLYunlong Li
Yunlong Li
In this study, numerical simulations were carried out to investigate the flow and heat transfer characteristics of jet array impingement cooling in the quasi-leading-edge channel of gas turbine blades. The influence laws of Reynolds number (Re, 10,000 to 50,000), hole diameter-to-impingement spacing ratio (d/H, 0.5 to 0.9), hole spacing-to-impingement spacing ratio (S/H, 2 to 6), and Prandtl number (Pr, 0.690 to 0.968) on flow performance, heat transfer performance, and comprehensive thermal performance were examined, and the corresponding empirical correlations were fitted. The results show that increasing the d/H and reducing the S/H can effectively reduce the pressure loss coefficient in the quasi-leading-edge channel. Increasing the Re, reducing the d/H, and increasing the S/H can effectively enhance the heat transfer effect of the target wall. When d/H = 0.6 at lower Reynolds numbers and S/H = 5 at higher Reynolds numbers, the comprehensive thermodynamic coefficient reaches its maximum values. The average Nusselt numbers and comprehensive thermal coefficients of the quasi-leading-edge channel for steam cooling are both higher than those for air cooling. The pressure loss coefficient of the quasi-leading-edge channel is most sensitive to the change in d/H but is not sensitive to the change in Re. The average Nusselt number of the quasi-leading-edge channel is most sensitive to the change in Re and is least sensitive to the change in Pr. The comprehensive thermal coefficient of the quasi-leading-edge channel is most sensitive to the change in Re. The findings may provide a reference for the design of a steam-cooling structure in the leading edge channel of high-temperature turbine blades.

8 February 2022 in Energies
Verified
Journal Article
Open access
PDF file
Zhen ZhaoZhen Zhao
Zhen Zhao
XLXU Liang
XU Liang
JGJianmin Gao
Jianmin Gao
Lei XiLei Xi
Lei Xi
QRQicheng Ruan
Qicheng Ruan
YLYunlong Li
Yunlong Li
In this study, Response Surface Methodology (RSM) and multi-objective genetic algorithm were used to obtain optimum parameters of the channels with frustum of a cone with better flow and heat transfer performance. Central composite face-centered design (CCF) was applied to the experimental design of the channel parameters, and on this basis, the response surface models were constructed. The sensitivity of the channel parameters was analyzed by Sobol’s method. The multi-objective optimization of the channel parameters was carried out with the goal of achieving maximum Nusselt number ratio (Nu/Nu0) and minimum friction coefficient ratio (f/f0). The results show that the root mean square errors (RSME) of the fitted response surface models are less than 0.25 and the determination coefficients (R2) are greater than 0.93; the models have high accuracy. Sobol’s method can quantitatively analyze the influence of the channel parameters on flow and heat transfer performance of the channels. When the response is Nu/Nu0, from high to low, the total sensitivity indexes of the channel parameters are frustum of a cone angle (α), Reynolds number (Re), spanwise spacing ratio (Z2/D), and streamwise spacing ratio (Z1/D). When the response is f/f0, the total sensitivity indexes of the channel parameters from high to low are Re, Z1/D, α and Z2/D. Four optimization channels are selected from the Pareto solution set obtained by multi-objective optimization. Compared with the reference channel, the Nu/Nu0 of the optimized channels is increased by 21.36% on average, and the f/f0 is reduced by 9.16% on average.

30 May 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Zhen ZhaoZhen Zhao
Zhen Zhao
Lei XiLei Xi
Lei Xi
JGJianmin Gao
Jianmin Gao
XLXU Liang
XU Liang
YLYunlong Li
Yunlong Li
In order to investigate the cooling mechanism of the turbine blade and to enrich and supplement the experimental study of the blade, a numerical study of a steam-cooled blade with five cooling channels was carried out based on the response surface model. The surface cooling efficiency and dimensionless temperature distribution of the steam-cooled blade were obtained with different mainstream inlet temperature, outlet pressure, pressure ratio of inlet to outlet, temperature ratio and flow ratio of steam to mainstream by using the flow-solid coupling numerical method. The influence of the working parameters on the cooling performance of air-cooled blade and steam-cooled blade, including the average cooling efficiency, temperature non-uniformity, and average dimensionless temperature, was comparatively investigated; the correlation equation of the working parameters on the cooling performance of the steam-cooled blade was obtained. The results show that the influence of mainstream inlet temperature and outlet pressure on the cooling performance of the steam-cooled blade is not significant; the cooling efficiency of the steam-cooled blade increases by 5.92%, 7.35% and 26.51% respectively as the mainstream inlet to outlet pressure ratio, the temperature ratio and the flow ratio of steam to mainstream increase; the dimensionless temperature increases by 3.74% as the temperature ratio increases and decreases by 0.93% and 4.09% as mainstream inlet to outlet pressure ratio and flow ratio increase; the temperature non-uniformity decreases by 4.09% and 30.08% respectively, as the mainstream inlet to outlet pressure ratio and temperature ratio increase and increases by 37.99% as the flow ratio increases; the effect of working parameters on air-cooled blade and steam-cooled blade is the same, but the steam-cooled blade has 14.06–17.81% higher cooling efficiency, 18.47–29.01% higher temperature non-uniformity and 1.86–2.58% lower dimensionless temperature compared to the air-cooled blade under the same working parameters; the correlation equation obtained by fitting the response surface model has higher accuracy.

27 July 2022 in Aerospace
Verified
Journal Article
Open access
PDF file
Lei XiLei Xi
Lei Xi
JGJianmin Gao
Jianmin Gao
XLXU Liang
XU Liang
Zhen ZhaoZhen Zhao
Zhen Zhao
ZYZhengheng Yang
Zhengheng Yang
YLYunlong Li
Yunlong Li
In this study, different layout schemes for an X-shaped truss array channel are designed to explore the application of an X-shaped truss array structure in the mid-chord region of turbine blades. The flow and heat transfer performance of X-shaped truss array channels for three layout schemes are numerically investigated. The influence laws of the subchannel height ratio (h/H, 0.2 to 0.4) regarding the cooling performance of the channel with three subchannels are also analyzed. Then, the corresponding heat transfer and friction correlations are obtained. The results show that the layout scheme has significant effects on the flow performance, heat transfer performance and comprehensive thermal performance of X-shaped truss array channels. Among the three layout schemes of X-shaped truss array channels, the single channel has the best flow performance, while the channel with three subchannels has the best heat transfer performance and a comprehensive thermal performance. At different Reynolds numbers, the average Nusselt numbers and comprehensive thermal coefficients of the X-shaped truss array channel with three subchannels range from 38.94% to 63.49% and 27.74% to 46.49% higher than those of a single channel, respectively, and from 5.68% to 18.65% and 11.61% to 21.96% higher than those of the channel with two subchannels, respectively. For the channel with three subchannels, the subchannel height ratio has a great influence on the flow performance, but has a relatively small influence on the heat transfer performance and comprehensive thermal performance of the channel. With the increase in subchannel height ratio, the friction coefficient and average Nusselt number of the channel with three subchannels both show a trend of first increasing and then decreasing, while the comprehensive thermal coefficient shows a slow decreasing trend at higher Reynolds numbers. As a result of comprehensive consideration, the channel with three subchannels at a subchannel height ratio of 0.25 has a better overall cooling performance and is more suitable for cooling the mid-chord region of gas turbine blades. The results may provide a reference for the application of truss array structures in the internal cooling of advanced high-temperature turbine blades in the future.

23 November 2022 in Computational Intelligence and Neuroscience
Verified
Journal Article
Open access
PDF file
FGFen Gu
Fen Gu
MDMei Deng
Mei Deng
XCXi Chen
Xi Chen
LALi An
Li An
Zhen ZhaoZhen Zhao
Zhen Zhao
In clinical applications, the classification of ultrasound images needs to be processed as an aid to diagnosis. Based on this, a hybrid model of cascaded deep convolutional neural network consisting of two different CNNs and a new classification method are designed and evaluated for its feasibility and effectiveness in ultrasound image classification. A total of 1000 pathological slides of patients with thyroid nodular lesions kept in the Department of Pathology of the First Affiliated Hospital of Lanzhou University, China, were retrospectively collected. After image acquisition, the images were randomly divided into training set, validation set, and test set in the ratio of 4:3:3. Three convolutional neural network models (VGG 19 model, Inception V3 model, and DenseNet 161 model) with pretraining parameters acquired on the training set were trained, and the models were combined to construct an integrated learning model, and the performance of the models in recognizing pathological images was evaluated based on the test set data. The experimental results show that the VGG 19 model is less effective in classification, with a correct rate of 88.20, which is lower than that of Inception V3 and DenseNet161 models (92.87 and 92.95). InceptionV3 and DenseNet161 models have significant advantages in terms of accuracy, number of parameters, and training efficiency, where the DenseNet161 model has faster convergence and better generalization performance, but occupies more video memory in the operation; moreover, the DenseNet161 operation time (1986.48s) and response time (16s) are better than the other two models. In addition, the integrated learning of InceptionV3 and DenseNet161 can improve the recognition of pathological images by a single model. Compared with other methods, the performance of the cascaded CNNs proposed in this study is significantly improved, and the multiview strategy can improve the performance of cascaded CNNs. The experimental results demonstrate the potential clinical application of cascaded CNNs, which can provide physicians with an objective second opinion and reduce their heavy workload, in addition to making the diagnosis of thyroid nodules easy and reproducible for people without medical expertise.

6 June 2023 in Actuators
Verified
Journal Article
Open access
PDF file
Lei XiLei Xi
Lei Xi
Zhen ZhaoZhen Zhao
Zhen Zhao
QRQicheng Ruan
Qicheng Ruan
ZYZhengheng Yang
Zhengheng Yang
XLXU Liang
XU Liang
YLYunlong Li
Yunlong Li
Inappropriate distributions of temperature and humidity will cause the failure of the spring-loaded actuators. Therefore, it is essential to understand the temperature and humidity distribution characteristics in typical spring-loaded actuators, to guarantee the safe operation of the spring-loaded actuators. In this work, a numerical simulation study on the temperature and humidity distribution characteristics in a spring-loaded actuator was conducted. The influence laws of ambient temperature, heater power, and heater size on the temperature and humidity distributions inside the spring-loaded actuator were analyzed. The practical empirical correlations for the spring-loaded actuators were fitted. The results show that the air temperature around and directly above the heater is the highest and the corresponding relative humidity is the lowest. Then, the air temperature gradually decreases, and the relative humidity increases with the lateral flow of air. When the ambient temperature increases from 233.15 K (−40 °C) to 313.15 K (40 °C), the minimum temperature inside the actuator is increased by 34%, the maximum humidity first increases and then decreases, and the maximum temperature on the heater surface is increased by 30%. When the heating power increases from 10 W to 150 W at ambient temperatures of 273.15 K and 298.15 K, the minimum temperature inside the actuator is increased by 3.40% and 3.61%, the maximum humidity is decreased by 51.97% and 58.63%, and the maximum temperature on the heater surface is increased by 30.33% and 33.25%, respectively. The influence of heater length, width, and height on the minimum temperature and maximum relative humidity inside the spring-loaded actuator is relatively small. Within the study range, the increase in heater length, width, and height makes the maximum temperature on the heater surface decrease by 9.15%, 7.59%, 4.63% at ambient temperatures of 273.15 K, and 10.74%, 9.01%, 4.73% at ambient temperature of 298.15 K, respectively. The results may provide a reference for predicting temperature and humidity distributions inside general spring-loaded actuators and provide a calculation basis for the design of their heaters.