This article proposes a novel compliance compensator that can measure six-axis force, torque and displacement. The proposed device can provide the information necessary for feedback control while protecting the robot from impact. The device was designed based on a 6-DOF parallel mechanism to have six-axis sensing and deform greatly at the rated load without failure. We designed new flexure links with flexure joints connected in series, which facilitates fabrication and stiffness analysis. Through the stiffness analysis, the measured force can be converted to displacement and the stiffness of the device can be customized to the desired value by simply adjusting the thickness of the links. The sensing performance was evaluated through experiments using a commercial force/torque sensor (F/T sensor) and precision stages. We also propose a displacement-based misalignment compensation method in a robotic peg-in-hole assembly using the proposed device. The method uses the intrinsic passive compliance of the device and measured displacement, not the force and torque. We reduced the reaction force generated in the peg-in-hole assembly by 92.6% through the proposed method. The proposed method is simple and intuitive, and can be used for automatic teaching of the manipulator.
28 August 2025 in IEEE Transactions on Power Electronics
In highlydynamic environments, such as industrial automation systems with frequent load changes or electric vehicles, ensuring both robustness and high-precision control remains challenging, particularly in the position control of permanent magnet synchronous motors. Sliding mode control (SMC) is widely used for its robustness, but traditional SMC methods often suffer from chattering and slow convergence, limiting overall system performance. To address these limitations, this study proposes a robust SMC approach incorporating a novel nonlinear sliding surface inspired by the supercritical pitchfork bifurcation concept. In addition, a new reaching law is introduced to attenuate chattering and ensure fast convergence of the sliding variable to zero within a finite time. The proposed method also integrates a proportional–integral observer (PIO) with the equivalent-input disturbance (EID) framework to enhance disturbance rejection under both matched and mismatched uncertainties. The stability of the proposed controller was verified using Lyapunov stability analysis, and its performance was validated through simulations and real-world experiments. Comparative evaluations demonstrated that the proposed reaching law significantly reduces chattering amplitude by over 50% and improves convergence speed by approximately 5.6 times faster than conventional methods. Furthermore, the system’s disturbance-rejection capability under matched and mismatched uncertainties is enhanced through the PIO + EID structure. These results confirmed the robust performance of the controller under unknown disturbances. This article is accompanied by a video that demonstrates the proposed control strategy and provides a comparison with traditional controllers.
17 January 2025 in Mechanical Systems and Signal Processing
Nowadays, many types of manipulators have been developed and used in lots of production processes. Force-based control methods or additional mechanical devices called Remote Center Compliance (RCC) have increased the system’s compliance and accuracy. However, the force-based control method’s operating speed is low, and the RCC cannot measure deflection. Thus it cannot calculate the position of the end-effector accurately. For accurate force and position control, it is necessary to measure the deflection of the RCC and to perform this, a different type of device than the existing RCC is required. This paper presents the necessity and possibility of developing an RCC capable of measuring the displacement of the end-effector and showing the displacement sensor’s feasibility using a 6 DOF parallel mechanism. In particular, we suggest that it is possible to make devices cheaper and more compact by using angular displacement sensors. Finally, we show the possibility of use in actual industrial sites through peg-in-hole simulation using the device.
The polymer cable is a widely used material in the cable-driven parallel robot (CDPR) system because of its many advantages such as high sensitivity, large workspace and so on. However, the accurate control of CDPR is not easy because of complicated response of the cable. In our previous study, the integrated cable model was derived. Based on the model, parametric studies were progressed in this paper. While operating CDPR, various parameters such as length, applied tension, and tensile rate can be changed and dominantly affect the dynamics of CDPR. For this reason, parametric study was based on these parameters. In this investigation, dynamic creep, hardening factor and short-term recovery were saturated as processing cyclic load. Each saturation rate was dominantly influenced by cable length and applied tension. As the tensile rate was increased, the dynamic creep was decreased. The hysteresis was the characteristic combining all of dynamics. So, the hysteresis also had saturation trends. When the exerted tension was decreased, the length of cable could be reduced or elongated because the creep and recovery occur at the same time.
9 January 2025 in IEEE Transactions on Instrumentation and Measurement
As robotics technology advances and the fifth industrial revolution unfolds, bringing robots closer to human life, research on ensuring human safety in shared workspaces has become crucial. Among these studies, manipulators, which are widely used in various fields, have gained prominence. Existing research predominantly employs sensor ring and sensor skin types for safety assurance by measuring robot-human distances. Sensor rings, with fewer sensors and lower costs, suffer from blind spots. Conversely, sensor skin types, despite being blind spot-free, incur high computational and fabrication expenses. Our proposed solution, RotOptiLink, integrates a rotational optical sensing device into manipulator links, combining the benefits of both types while mitigating their drawbacks. RotOptiLink utilizes a slip ring mechanism, enabling the outer ring, equipped with distance sensors, to rotate while maintaining contact with the inner ring, which carries power and signal processing lines. This setup allows for the detection of approaching individuals and obstacles without blind spots, even with a small number of sensors. We mathematically generalize design parameters, validate them experimentally, and demonstrate omnidirectional obstacle sensing on a three-axis manipulator.