Considering the well documented, almost ubiquitous nature of microplastics in different environments, the exposure of pregnant women to microplastics may pose risks to the unborn children. The study focused on investigating the presence of microplastics in amniotic fluid and placenta, and brings the first evidence of the simultaneous presence of microplastics and additives in both human amniotic fluid and placentas. In total, 20 samples of amniotic fluid and placenta from 10 patients were analyzed for the presence of microplastics and plastic additives by Fourier transform infrared spectroscopy - attenuated total reflectance (FTIR-ATR) after alkaline digestion with KOH. In 9 out of 10 patients, microplastics or additives were found in amniotic fluid, placenta, or both. Specifically, 44 particles of microplastics and polymer additives were identified in all samples. Chlorinated Polyethylene (CPE) and Calcium zinc PVC Stabilizer with particle sizes between 10 and 50 μm prevailed. Although all women involved in this study, who provided placenta and amniotic fluid samples, experienced physiological, singleton pregnancies complicated with preterm prelabour rupture of membranes (PPROM), it is too early to draw any conclusions and more research is needed.

Plastic particles smaller than 5 mm, i.e., microplastics, have been detected in a number of environments. The number of studies on microplastics in marine environments, fresh water, wastewater, the atmosphere, and the human body are increasing along with a rise in the amounts of plastic materials introduced into the environment every year, all contributing to a range of health and environmental issues. Although the use of primary microplastics has been gradually reduced by recent legislation in many countries, new knowledge and data on these problems are needed to understand the overall lifecycle of secondary microplastics in particular. The aim of this review is to provide unified information on the pathways of microplastics into the environment, their degradation, and related legislation, with a special focus on the methods of their sampling, determination, and instrumental analysis. To deal with the health and environmental issues associated with the abundance of microplastics in the environment, researchers should focus on agreeing on a uniform methodology to determine the gravity of the problem through obtaining comparable data, thus leading to new and stricter legislation enforcing more sustainable plastic production and recycling, and hopefully contributing to reversing the trend of high amounts of microplastics worldwide.

Climate change is creating new challenges for water supply worldwide, making the search for new sources of water vital. As mine water could serve as a potential source, this study investigated the presence of microplastics in water from terminated deep mines in the largest coal basin in the Czech Republic, as well as in water from nearby shallow wells. The particles found were analyzed for size, polymer composition, color and morphology using the ImageJ tool, infrared spectroscopy with Fourier transform (FTIR) and an optical stereomicroscope with a digital camera. Microplastics were detected in all tested sites. Their range accounted for 2.5-17.5 items/L for mine water samples and 2.5-20 items/L for well samples, with fibers being the dominant type. The average width of particles from mine water and wells amounted to 58 µm; 71 µm, length to 655 µm; 501 µm and area to 22,067 µm2; 28,613 µm2, respectively. Blue color was prevalent, among materials, in both cases, plastic coated paper was found dominant to Polyethylene terephthalate (PET), Polyester (PES), Tetrafluoroethylene-perfluoro (Propyl Vinyl Ether) - Copolymer (TFE-PPVE), and polypropylene (PP). The research provides the first evidence of microplastics' presence in underground waters from deep mines and shallow wells in the same area. The data suggest that it is almost impossible to find underground water sources free of microplastic contamination. In this context, atmospheric contamination from mine ventilation and infiltration through terminated mines were identified as potential sources, while infiltration through soil and rock formations is unlikely given the geological composition. The results of this study can serve as a relevant basis for further research on microplastics in mine waters. Additionally, the conclusions can advance the development in remediation technologies of microplastics from deep underground waters and their implementation in practice, particularly in light of upcoming legislation.

This article summarizes the results of a research study that was focused on the possibility of removing Cr (VI) from aqueous solution, using low-cost waste biomaterial in a batch mode. A set of seven biosorbents was used: Fomitopsis pinicola, a mixture of cones, peach stones, apricot stones, Juglans regia shells, orange peels, and Merino sheep wool. Three grain fractions (fr. 1/2, fr. 0.5/1.0, and fr. 0/0.5 mm) of biosorbents were studied. The aim was to find the most suitable biosorbent that can be tested with real samples. The influence of other factors on the course of biosorption was studied as well (chemical activation of the biosorbent, pH value, rotation speed during mixing, temperature, and the influence of biosorbent concentration). The use of chemical activation and adjustment of the pH to 1.1 to 2.0 make it possible to increase their sorption capacity and, for some biosorbents, to shorten the exposure times. Two kinetic models were used for the analysis of the experimental data, to explain the mechanism of adsorption and its possible speed control steps: pseudo-first and pseudo-second-order. The pseudo-second-order kinetic model seems to be the most suitable for the description of the experimental data. The thermodynamic parameters suggest that the biosorption was endothermic and spontaneous. In the biosorption equilibrium study, the adsorption data were described by using Langmuir and Freundlich adsorption isotherms. The Langmuir model was applicable to describe the adsorption data of all biosorbents. Both models are suitable for chemically treated sheep fleece and peach stones.

This article describes an experimental study aimed at investigating the potential use of recycled rubber granulate from waste tires of fractions 0/1 and 1/3 mm in cement composites as a 100% replacement for natural aggregates. The use of waste in the development and production of new building materials represents an important aspect for the sustainability and protection of the environment. This article is focused on the sound-absorbing and thermal-insulating properties of experimental cement composites based on recycled rubber from waste tires. The article describes the grain characteristics of recycled rubber, sound absorption capacity, thermal conductivity and strength characteristics. The results of this research show that the total replacement of natural aggregate with recycled rubber in cement composites is possible. Replacing natural aggregate with recycled rubber has significantly improved the thermal and acoustic properties of the prepared cement composites, however, at the same time; there was also the expected decrease in the strength characteristics due to the elasticity of rubber.

In line with the requirements of the circular economy, the European Union’s waste management legislative changes also concern the treatment of sewage sludge. Although sewage sludge production cannot be prevented, its quantities may be reduced by the synergetic effect of energy recovery via choosing a proper technology. Sewage sludge is difficult to apply as fuel alone, because of its high moisture and ash content. However, its energy use will be increased by adding suitable waste materials (different types of plastics, waste tires and paper rejects). Most recently, the thermal utilization of sewage sludge via incineration or pyrolysis has grown in importance. This article describes the fuel parameters of particular waste materials and of their blends with sewage sludge in connection with laboratory-scale thermal decomposition in an inert atmosphere, for their potential use in a semi-pilot plant pyrolysis unit. For pyrolytic application, the results of thermogravimetric analysis are needed in order to know the maximal temperature of thermal decomposition in an inert atmosphere, maximal mass losses, and weight loss rates. The samples of different thermoplastics mixed with sewage sludge, and low-density polyethylene blends with sewage sludge, had the lowest residual masses (70–74%) and the highest weight loss rates (11–19%/min). On the other hand, the blend of polyester rejects from tire processing, paper rejects and sewage sludge had the second highest residual mass (60%) and the lowest weight loss rate (3%/min).