Hydrogen is an essential vector for transitioning today’s energy system. As a fuel or reactant in critical industrial sectors such as transportation and metallurgy, H2 can diversify the energy mix and supply and provide an opportunity to mitigate greenhouse-gas emissions. The pyrolysis of methane in liquid catalysts represents a promising alternative to producing hydrogen, as its energy demand is comparable to steam methane reforming, and no CO2 is produced in the base reaction. In this work, methane pyrolysis experiments were conducted using a graphite crucible filled with liquid ternary Cu-Ni-Sn alloys at 1160.0 °C. A statistical design of experiments allowed the generation of a model equation that predicts the achievable conversion rates in the ranges of the experiments. Furthermore, the experimental results are evaluated considering densities as well as surface tensions and viscosities in the investigated system, calculated with Butler and KRP equations, respectively. The highest methane conversion rate of 40.15% was achieved utilizing a melt of pure copper. The findings show that a combination of high catalytic activity with a high density and a low viscosity and surface tension of the melt results in a higher hydrogen yield. Furthermore, the autocatalytic effect of pyrolysis carbon is measured.
In light of the growing interest in hydrogen as an energy carrier and reducing agent, various industries, including the iron and steel sector, are considering the increased adoption of hydrogen. To meet the rising demand in energy-intensive industries, the production of hydrogen must be significantly expanded and further developed. However, current hydrogen production heavily relies on fossil-fuel-based methods, resulting in a considerable environmental burden, with approximately 10 tons of CO2 emissions per ton of hydrogen. To address this challenge, methane pyrolysis offers a promising approach for producing clean hydrogen with reduced CO2 emissions. This process involves converting methane (CH4) into hydrogen and solid carbon, significantly lowering the carbon footprint. This work aims to enhance and broaden the understanding of methane pyrolysis in a liquid metal bubble column reactor (LMBCR) by utilizing an expanded and improved experimental setup based on the reactor concept previously proposed by authors from Montanuniversitaet in 2022 and 2023. The focus is on investigating the process parameters’ temperature and methane input rate with regard to their impact on methane conversion. The liquid metal temperature exhibits a strong influence, increasing methane conversion from 35% at 1150 °C to 74% at 1250 °C. In contrast, the effect of the methane flow rate remains relatively small in the investigated range. Moreover, an investigation is conducted to assess the impact of carbon layers covering the surface of the liquid metal column. Additionally, a comparative analysis between the LMBCR and a blank tube reactor (BTR) is presented.
In terms of production volume, aluminium is the leading metal in non-ferrous metallurgy. In particular, the recycling of aluminium-containing residues has strongly increased in recent years and will continue to gain importance in the future. Due to the high affinity of aluminium to oxygen, the oxidation of the molten bath is unavoidable, which leads to the formation of dross on the surface. This has a high content of metallic aluminium and therefore represents a valuable residual material that must be further processed. In the presented work, a study is conducted on the formation and possible further processing of aluminium dross. Within the scope of this experimental work, the pyrometallurgical treatment of Al-dross in the salt drum furnace was evaluated on the basis of an experiment in a TBRC (top blown rotary converter) by adding a salt mixture. In addition, the behaviour of special metals, in particular the rare earth elements (REEs), was investigated during such a melting process. This knowledge will be particularly important in the future, as inadequate scrap processing leads to more of these partially valuable contaminants entering the aluminium scrap cycle. The result of the experimental study was that the metal yield of the dross used in the melting experiment at the Chair of Nonferrous Metallurgy was higher than that achieved by external reprocessing. Regarding the distribution of the rare earths, there was a direct transition of these from the dross into the emerging salt slag phase.
4 March 2021 in BHM Berg- und Hüttenmännische Monatshefte
Zusammenfassung: Aluminiumschrott ist häufig mit einer Vielzahl an Stoffen verunreinigt, wie Kunstoffen, Dichtungen, Ölen und Holz, oder liegt in lackierter bzw. beschichteter Form vor. Dabei handelt es sich um organische Bestandteile, welche in den Schmelzöfen zu Reaktionen und damit zum Verlust von metallischem Aluminium führen. Im Rahmen dieses Beitrags erfolgt eine Erläuterung der industriell üblichen Verfahren zur Verarbeitung von minderwertigen Al-Schrotten, welche einen hohen Organikanteil aufweisen. Typischerweise kommen diese in Refinern zum Einsatz, wo Schmelzsalze Anwendung finden. Dabei erfolgt die Herstellung von Gusslegierungen, wozu auch Desoxidationsgranalien, welche in der Stahlherstellung Verwendung finden, zählen. Eine weitere Möglichkeit zur Erzeugung dieser Produkte bietet der Schmelzprozess im Zweikammerofen, wo durch Pyrolyse vorab ein hoher Anteil organischer Bestandteile entfernt werden kann. Im experimentellen Teil des Beitrags finden Laboruntersuchungen statt, um Schmelzausbeuten von gemischtem Al-Schrott mit hohem Organikgehalt zu bestimmen. Hierbei werden die metallurgischen Rahmenbedingungen dahingehend eingestellt, dass eine Vergleichbarkeit mit den industriell eingesetzten Schmelzaggregaten gegeben ist. Die besten Ergebnisse konnten dabei durch die Anwendung von Schmelzsalzen erreicht werden. Bei der Verarbeitung minderwertiger Schrotte im Zweikammerofen führt eine vorgeschaltete Pyrolyse zur Erhöhung der Schmelzausbeuten und zur Verringerung der Krätzemengen.
Zusammenfassung: Die katalytische Zersetzung von Methan (CH4) in flüssigen Metallen ist als vielversprechende Technologie für die Herstellung von CO2-freiem Wasserstoff (H2) zu sehen. Bei diesem Verfahren wird CH4 in ein flüssiges, katalytisch aktives Metall eingebracht und zersetzt, wodurch H2 und fester Kohlenstoff entstehen. Um in diesem strategisch wichtigen Forschungssegment einen wesentlichen Beitrag leisten zu können, wurde an der Montanuniversität Leoben die dafür erforderliche Infrastruktur in Form eines Forschungszentrums für Wasserstoff und Kohlenstoff geschaffen. Dieser Artikel gibt zuerst einen Überblick zu den bisher entwickelten Versuchssetups im Labormaßstab, die für die Pyrolyse von Methan im Metallbad konzipiert wurden. Anschließend erfolgt die Vorstellung der im Forschungszentrum errichteten Pilotanlage, wobei auf die Aggregate eingegangen wird, die für die Untersuchung verschiedener Prozessparameter der CH4-Pyrolyse sowie für eine umfassende Produktstrombehandlung erforderlich sind. Das zentrale metallurgische Aggregat stellt eine Induktionsschmelzanlage dar, welche sowohl bei Umgebungsdruck als auch bei bis zu 10 bar betrieben werden kann. Die anschließende Behandlung des Produktstroms erfolgt mittels Heißgasfilter und Wärmetauscher, um den bei der Methanzersetzung entstehenden festen Kohlenstoff sowie weitere Zersetzungsprodukte abzutrennen. Mittels einer Membrananlage ist es anschließend möglich, den partikelfreien Gasstrom, der hauptsächlich aus Wasserstoff und nicht umgesetztem Methan besteht, an H2 anzureichern. Durch den Einsatz einer thermischen Nachverbrennungsanlage werden schlussendlich alle bei diesem Prozess entstehenden Produkte vollständig neutralisiert.