In this paper, microlens array (MLA) templates with high filling factors were prepared by combining a thermal reflow method and parylene chemical vapor deposition (CVD). Then photoresist MLAs were replicated from the MLA templates by using ultraviolet nanoimprint technology. The surface morphology of the replicated photoresist MLAs was characterized by scanning an electron microscope and optical microscope. Results show that the photoresist MLAs have a relatively smooth surface, and the filling factor has been improved obviously. Also, the surface profiles of the MLAs were measured. The optical imaging properties of the MLAs were also characterized, and they had a relatively good imaging performance. Finally, the photoresist MLAs were applied on organic LEDs (OLEDs), and their luminance and current efficiencies were measured. Results show that the current efficiency of the OLEDs increased by about 42.41%, 29.01%, and 35.51%, respectively, for OLEDs with circular, hexagonal, and square MLAs. All the results above indicate that it is a simple and effective process to prepare MLA templates with high filling factors by combining thermal reflow and CVD techniques, and the prepared photoresist MLAs have great application potential in OLED areas.
Front surface texturing is a common method used to improve the optical performance of photovoltaic devices. However, traditional texturing techniques may be challenging in some cases, such as when dealing with ultra-thin substrates. Textured polymer films on such devices would be an alternative approach. This paper reports a study of NOA81 thin films with a bionic lotus leaf surface structure on monocrystalline silicon solar cells. Inspired by the surface structure of natural lotus leaves, we successfully prepared a bionic lotus leaf microstructure film on the surface of solar cells based on NOA81 using polydimethylsiloxane (PDMS) polymer and nanoimprinting methods. Scanning electron microscopy (SEM) images showed that the surface structure of the NOA81 thin film was the same as that of natural lotus leaves. A UV-Vis spectrophotometer with an integrating sphere was used to measure the reflectance of the textured NOA81 film on the silicon wafer. Results showed that the textured NOA81 film could effectively reduce the reflectance of the silicon wafer surface. We also used finite-difference time-domain (FDTD) simulation to verify this conclusion further. Finally, the I-V characteristics of the prepared solar cells with the textured NOA81 film were investigated, and the highest photovoltaic efficiency was measured to be about 16.07%, effectively improving the photoelectric conversion efficiency. In addition, the film with textured NOA81 can be used as a protective film for monocrystalline silicon solar cells.
4 July 2023 in Journal of Sol-Gel Science and Technology
Light trapping micro-nano structures have been widely used to optimize the function of solar cell devices, especially microlens arrays (MLAs). In this article, we first prepared composite films by using sol-gel technology and the spin coating method, and then constructed heteromorphic MLAs on the surface of the composite films by using thermal reflow and UV nanoimprint technology; the substrate used was the silicon solar cell. Finally, the performance of the cells was improved. Optical transmission properties and surface morphology of the organic–inorganic hybrid films were detected by using a UV-Vis spectrometer and atomic force microscopy, respectively; it was revealed that the hybrid films had relatively excellent optical transmission performance in the visible light range. Surface structure of the hybrid film MLAs were detected by using SEM. At the same time, the optical imaging capabilities of MLAs were studied by using optical microscopy. Besides, the contact angles of the MLAs were also measured. It can be clearly seen that the prepared MLAs have a regular arrangement, clean appearance, and good imaging capabilities (from the actual test results). Finally, the various parameters of the silicon solar cells with hybrid film MLAs were studied. In addition, the power conversion efficiency (PCE) values increased by about 10.48% for the silicon solar cell with circular MLAs, compared to the silicon solar cell without a structure. The results show a concise and effective method to prepare organic–inorganic hybrid film MLAs on silicon solar cells, with significant improvement in photoelectric conversion efficiency.
Poly (methyl methacrylate) (PMMA)-doped organic-inorganic composite films are prepared on flexible substrates through a combination of the sol-gel technique and the spin-coating method. Circular and hexagonal microlens arrays (MLAs) are then built into the composite films by using ultraviolet nanoimprint technology. Atomic force microscope and ultraviolet spectrophotometer characterization results of the films show that the films have low surface roughness and good optical transmittance. A scanning electron microscope is used to observe the surface morphology of the MLAs, and the results show that the prepared MLAs are regular and neat. The surface profiles of the MLAs are also measured by using a surface profiler. Optical microscopy results show that the prepared MLAs have good optical imaging properties. Finally, the MLAs are applied on the green organic light-emitting diodes (OLEDs), and the influence of the shape and diameter of the MLAs on the luminance and current efficiency of the OLEDs is discussed. Results indicate that there is a relatively high enhancement of the current efficiency and luminance for the OLEDs with hexagonal MLAs and a single microlens height of 9 µm, where the luminance can reach , and the current efficiency can be enhanced by about 20.1%. Furthermore, there is a higher enhancement of the luminance and current efficiency for the OLEDs with PMMA-doped MLAs than that of the OLEDs with no PMMA-doped MLAs. Based on these results, we believe that the obtained PMMA-doped composite film MLAs on flexible substrates have important applications in the flexible OLEDs displays areas.