In this study, a high-resolution, two-dimensional (2D), time-dependent hydrodynamic model of the St. Lawrence fluvial estuary was developed with the objective of documenting the tidal hydrodynamics of this complex yet poorly understood region. The hydrodynamic model solves the shallow-water equations over a finite-element–discretized domain, with an average spatial resolution of 50 m, and includes a drying–wetting component for the treatment of shallow intertidal areas. The numerical terrain model is composed of high-density topographic data and detailed friction fields associated with bottom substrate and macrophytes. Calibration and validation were carried out using recently acquired data for water level and velocity. Results show very good accuracy in water levels, with prediction skills higher than 0.99 at all stations (where a skill of 1 means perfect agreement between model and observations in terms of their relative average error) and root-mean-square errors (RMSEs) less than 5% of local tidal ranges downstream; at upstream stations where tidal ranges are significantly reduced, RMSEs were lower than 6 cm. Discharges were reproduced with similarly good accuracy, with errors lower than 6% of the maximum observed discharges at 11 of the 13 surveyed transects; the two remaining sections are subject to larger interpolation and bathymetric uncertainties. In this paper, critical aspects of model development are discussed, including the 2D approximation, temporal and spatial resolution, bathymetric uncertainty, error in the boundary conditions, and calibration under nonstationary conditions. This work is the first part of a two-part investigation serving as a methodological framework for model setup, calibration, and validation in large tidal rivers.
14 August 2018 in Journal of Geophysical Research: Oceans
Knowledge of tidal flows in rivers and estuaries is often scarce yet vital in determining flushing properties and sediment transport rates. While many rivers still remain ungauged, methodological difficulties often arise in gauged systems, resulting in short flow records compared to historical water level data. Notwithstanding, discharge reconstructions in estuaries are possible using indirect methods based on long‐term tidal data. In this paper, we revisit the method of cubature, integrating the continuity equation for discharges at different sections. The method consists in computing temporal changes in water volume from simultaneous tidal heights readings along the river and storage width estimations. These water balance estimates remain challenging to produce, because they require spatial interpolation of gappy tidal records and an accurate representation of inundated areas over time. Improvements on the method are made by using a 1‐D nonstationary tidal harmonic model that provides continuous tidal data along the estuary, with no temporal or spatial gaps. Second, a 2‐D finite element discretization is used to compute the time‐varying wetted surface area, relying on detailed topographic data over intertidal flats. The method is applied to the St. Lawrence fluvial estuary (SLFE) and validated against discharge data collected along nine cross sections of the river, reaching relative RMSE below 4% of the diurnal tidal discharge range at downstream locations and below 9% upstream. One year reconstructions conducted in the SLFE also show the potential of the method to reproduce the tidal discharge variability along the tidal‐river continuum, for a wide range of temporal scales.
1 September 2017 in Journal of Waterway, Port, Coastal, and Ocean Engineering
This is the second part of an investigation aimed at documenting the tidal hydrodynamics of the St. Lawrence fluvial estuary (SLFE). In Part I, the calibration and validation of a high-resolution, two-dimensional (2D), time-dependent hydrodynamic model of the SLFE was presented. Herein, the process-based (structural) validation procedure used to quantitatively assess the ability of the model to reproduce spatial and temporal patterns observed in the field data is presented. Tidal and flow features were found to be reproduced satisfactorily in terms of their lateral and longitudinal variability at both the intratidal and fortnightly scales. These properties can be used to describe the real system dynamics, including flooding–drying processes, tidal propagation and modulation, and transient momentum balance, providing insights into the general physical processes of the SLFE and of large tidal rivers globally.
1 June 2011 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
The main contribution from this paper includes the hydrodynamic modeling and morphological analysis of Lake Água Preta in Belém city, Pará State, Brazil. The lake bathymetry was taken through the data provided by COSANPA (the local sanitation and water supply company) dating back to 1975, and from a 2009 field study. Both bathymetries produced two terrain elevation models, which were used for morphological analysis and hydrodynamic simulations. The morphological analysis has revealed that, from 1975 to 2009, the annual mean rate of sedimentation varies between 23,065 and 29,081 m3/year. Through this result, the sedimentation time of Lake Água Preta, from 2009, has been calculated, which varies between 295 and 381 years, maintaining the same rate of sedimentation, water consumption and pumping. The hydrodynamic model simulated the depths and velocities, showing a slight flow with velocities ranging from 0 to 33 cm/s. This flow is established between water input and output of the lake, which is used as reservoir of Belém city
1 March 2011 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
This work describes the steps required to construct a hydrodynamic model of the Guajará Bay, using Geographic Information Systems and the Finite Element Method. An overview of the problem that motivates this modelling procedure, i.e., the pollutant dispersion, is presented. The computer software used is then discussed, stressing the links between the data model entities. The calibration procedure is described. The methods used to obtain field data and the results obtained are presented, alongside the main flow patterns of the water. The simulations and applications of the model are discussed at the end of the paper
22 January 2001 in Communications in Numerical Methods in Engineering