André Luiz Amarante Mesquita

Prof. Dr. André Luiz Amarante Mesquita

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
18 July 2024 in Heliyon
Verified
Journal Article
Open access
ATAbeyo Mayo Tchada
Abeyo Mayo Tchada
NTNsah-Ko Tchoumboué
Nsah-Ko Tchoumboué
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita
PHPatrick Hendrick
Patrick Hendrick
Pump As Turbine (PAT) utility represents a major advance in the field of hydraulic engineering. This work aims to improve the PAT performance characteristics. The sharp impeller leading edge (original impeller) was revealed by flow analysis as exhibiting negative effects on the PAT performances due to flow separation and flow misalignment. The performances of rounded and original impeller leading edge were studied by Computational Fluid Dynamic (CFD) method carried out on ANSYS CFX. Although impeller leading edge rounding has notably improved the performances in off design conditions, the difference of efficiency between the both impeller types was decreasing when increasing the discharge. The hydraulic head generated by the rounded impeller leading edge was also slightly higher at part load conditions, but when increasing the discharge, the difference between the both heads became negligible. It appeared from numerical simulations that the impeller leading edge rounding allows to decrease the hydraulic losses of the individual sub-domains except the outlet pipe. For the seek of a comprehensive analysis, the significant losses were computed for the two impeller geometries. It was observed that the shock losses and swirling losses of the rounded impeller leading edge were lower at part load conditions, but when increasing the discharge, the both losses were lower for the original impeller geometry. The rounded impeller leading edge exhibited as well lower wall frictional losses for the entire operating range of discharge.

22 May 2022 in Energy Conversion and Management
Verified
Journal Article
Closed access
JPJessé Luís Padilha
Jessé Luís Padilha
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita

1 March 2014 in Brazilian Journal of Chemical Engineering
Verified
Journal Article
Open access
PDF file
LGL. M. Gomes
L. M. Gomes
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita
This paper presents a comparative study of the critical pickup and saltation velocities of particles in horizontal pipelines for pneumatic conveying design. A comparative study is performed using different existing correlations in the literature for the determination of the minimum velocity of transport as a function of the particle and pipe diameter, particle density, solid mass flow rate and particle sphericity. Their limitations and difficulties in predicting those critical velocities are analyzed. For the pickup velocity, an experimental study was also carried out in order to support the analysis. Recommendations are presented on the use of such correlations

10 October 2021 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Closed access
PDF file
DSDavi Edson Sales e Souza
Davi Edson Sales e Souza
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita
CBClaudio Blanco
Claudio Blanco

1 March 2011 in Journal of the Brazilian Society of Mechanical Sciences and Engineering
Verified
Journal Article
Open access
PDF file
MBMaria de Lourdes C. Barros
Maria de Lourdes C. Barros
MSManoel José dos Santos Sena
Manoel José dos Santos Sena
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita
CBClaudio Blanco
Claudio Blanco
YSYves Secretan
Yves Secretan
This work describes the steps required to construct a hydrodynamic model of the Guajará Bay, using Geographic Information Systems and the Finite Element Method. An overview of the problem that motivates this modelling procedure, i.e., the pollutant dispersion, is presented. The computer software used is then discussed, stressing the links between the data model entities. The calibration procedure is described. The methods used to obtain field data and the results obtained are presented, alongside the main flow patterns of the water. The simulations and applications of the model are discussed at the end of the paper

23 January 2021 in Environmental Monitoring and Assessment
Verified
Journal Article
Closed access
PDF file
POPablo Abreu de Oliveira
Pablo Abreu de Oliveira
CBClaudio Blanco
Claudio Blanco
André Luiz Amarante MesquitaAndré Luiz Amarante Mesquita
André Luiz Amarante Mesquita
DLDavid Franco Lopes
David Franco Lopes
MFManoel Domingos Castro Furtado Filho
Manoel Domingos Castro Furtado Filho