The next-generation (5G/6G) wireless communication aims to leapfrog the currently occupied sub-6 GHz spectrum to the wideband millimeter-wave (MMW) spectrum. However, MMW spectrums with high-order modulation schemes drive the power amplifier (PA) at significant back-off, causing severe nonlinear distortions, thus deteriorating the transceiver’s (TRXs) modulation process. Typically, the TRX efficacy is quantified with standardized linearization matrices, which take advantage of different predistortion (PD) schemes to handle deep compression of the PA. In this regard, TRX baseband signals are mostly linearized in the digital domain, where digitally controlled linearization needs higher sampling rates due to increasing MMW bandwidths to compensate for intermodulation (IMD) products, resulting in increased system cost and power consumption. Alternately, the digitally controlled analog-based linearization, i.e., the hybridization of digital predistortion (DPD) and analog predistortion (APD), is highly productive and cost-effective for fulfilling the linearized energy-efficient design vision of MMW networks. Therefore, this paper puts an extensive spotlight on the progress in PD-based linearization for 5G and beyond communications. It first provides background information on the advancements of PD schemes through recent surveys, then classifies the general roadmap of PD waveform processing across the TRX system models as preliminary. After this, we present three prominent PD architectures and their design approaches with intrinsic performance metrics. Finally, we explore four case studies encompassing PD operation under certain nonlinear constraints of different communication schemes. We examine the suitability of PD-based linearization solutions, both existing and proposed till the first quarter of 2022, and identify the potential prospects in this domain.
29 January 2025 in IEEE Transactions on Microwave Theory and Techniques
This article presents a system-level analysis of the maximum achievable data rate in a phased array wireless link limited by the RF front end (FE) technology and frequency-dependent noise and linearity performance. Frequency scalable circuit models of RF front-end amplifiers and front-end switch were created from literature data of 22-nm fully depleted silicon on insulator (SOI) CMOS technology. The analysis was continued by optimizing the transmit and receive array sizes and center frequency for minimal dissipated power for a given data rate and link range. A front-end circuit with a center frequency of 150 GHz is predicted to satisfy 6G data rate (120 Gb/s) and range (100 m). Consequently, a prototype RF front end was implemented and measured to verify the validity of the frequency scalable behavioral models. The front-end switch was designed for minimal impact on transmitter (TX) output power and receiver (RX) noise figure (NF) reaching saturated output power of 9.7 dBm and 11.4-dB noise figure for transmitter and receiver at 142 and 144 GHz, respectively. The transmitter was measured with a 5G new radio (NR) orthogonal frequency-division multiplexing (OFDM) 800-MHz multicarrier signal achieving 2.8-dBm output power while meeting 5G adjacent channel power ratio (ACPR) and error vector magnitude (EVM) specifications. The results from the system analysis together with the implemented front end give a strong indication of the need for highly linear receiver mixers, multiple-input multiple-output (MIMO) schemes, and RF bandwidth (BW) extension techniques to reach 6G data rate expectations with reasonable power consumption and array sizes.
22 May 2023 in IEEE Journal of Solid-State Circuits
This article presents a chip-to-chip (C2C) interface for constructing reconfigurable phased arrays to be used in fifth-generation (5G)/sixth-generation (6G) wireless systems. The C2C interface further facilitates building phased array panels by allowing the use of grid-based PCB routing, thus providing flexibility in the system design. An eight-element RFIC capable of handling two independent data-streams is fabricated using 45-nm CMOS technology. The RFIC incorporates four C2C interfaces operating at 27 GHz, two C2C interfaces operating at 9 GHz, and a complex baseband (BB) with single-sided bandwidth in excess of 400 MHz. The architecture is tested by flip-chip bonding two fabricated RFICs on an eight-layer Megtron 7 PCB. In this article, only the receiver path of the RFIC and the phased array is described. Performance of both the single RFIC and the combination using the 27-GHz C2C interface is demonstrated using conductive and over-the-air (OTA) measurements. OTA measurements are conducted using 5GNR FR2 OFDM waveforms with a signal bandwidth of up to 800 MHz. The measured RF to BB conversion gain for a single element is larger than 23 dB and the minimum measured noise figure (NF) is 6.2 dB. The nominal dc power consumed by the receiver per element per stream is 116.5 mW. The RFIC occupies a normalized area per element per data stream of 2.7 mm 2 . The RFIC is capable of supporting dual-polarized antennas or in a large-scale panel utilizing the same antenna elements to two independently weighted data streams as part of the hybrid beamforming architecture.
This paper presents an active RF phase shifter, targeted towards 5G wireless systems, which uses an IQ vector modulator (IQVM) topology with a 10 bit cartesian codebook. The circuit is designed using 45 nm CMOS SOI technology. To generate the I and Q basis vectors for the IQVM, a tunable polyphase filter with a novel tuning mechanism is used, which allows operation over an octave of a frequency range, from 22 GHz to 40 GHz. The RF bandwidth of the proposed phase shifter is 2.5 GHz and can provide in excess of 8 dB of fine gain control over 360 degrees of phase shift. Active area occupied is 0.2 square millimeter. The total DC power consumed from 1 V supply is 36 mW.
21 July 2022 in IEEE Transactions on Circuits and Systems I: Regular Papers
Stacked MOS power amplifiers (PA) are commonly used in SOI nodes but also have the potential to be realized in bulk CMOS nodes. In this paper they are analyzed in millimeter wave regimes. The study focuses on the key limiting factors and in particular the optimum number of transistors from which the key performance parameters such as maximum possible operating frequency, output power, and efficiency are achieved. Based on the analysis, design trade-offs of stacked MOS PAs are presented. The frequency dependency of the optimum load presented to each stack is analyzed to express the overall performance of the mentioned PA topologies as a new optimization method. Additionally, it is shown how the optimal load variations translate into amplitude-to-amplitude/phase (AM-AM/PM) conversion distortions. The validity of the analysis is examined against simulations. The simulations are performed based on 8M1P CMOS 28nm technology and electromagnetic simulations in ADS Momentum.
An approach to determine the optical modal gain spectra in multiple quantum-well semiconductor lasers based on InP in terms of the current at electrodes is presented. The link between the current at the electrodes and the density of carriers inside each quantum well was provided by rate equations with the inclusion of carrier transport effects. Description of hole dispersion is based on a 4 × 4 Luttinger–Kohn Hamiltonian and was done with the electrostatic effects of the carrier charges. Electrostatic effects were included via a self-consistent solution of electron and hole wave equations and the Poisson equation. The optical gain for the TE (transverse electric) mode has been determined with the inclusion of non-Markovian effects, Coulombic enhancement, and band-gap renormalization. The theoretical approach was compared with experimental measurements of the optical gain on a laser structure consisting of four quantum wells using the Hakki–Paoli method. The important role played by the leakage current was revealed when the results were compared. PACS No.: 73.63.Hs, 78.20.Bh, 78.20.Ci