An accurate and effective method combining ion chromatography (IC) and inductively coupled plasma optical emission spectrometry (ICP-OES) was applied in this work to qualitatively and quantitatively analyze individual and co-existing iodide (I−) and iodate (IO3−) at various concentrations. More specifically, a very strong linear relationship for the peak area for the co-existing I− and IO3− ions was reached, and a high resolution value between two peaks was observed, which proves the effectiveness of our combined IC-ICP-OES method at analyzing iodine species. We observed lower accessible porosity for the diffusion of both I− and IO3− in samples of bentonite clay using IC-ICP-OES detection methods, where the effective diffusion coefficient varied based on the anion exclusion effect and the size of the diffusing molecules. In fact, the distribution coefficients (Kd) of both I− and IO3− were close to 0, which indicates that there was no adsorption on bentonite clay. This finding can be explained by the fact that no change in speciation took place during the diffusion of I− and IO3− ions in bentonite clay. Our IC-ICP-OES method can be used to estimate the diffusion coefficients of various iodine species in natural environments.
Clay rock in the Tamusu (TMS) area in the Inner Mongolia province is one candidate as a geological disposal site for highly radioactive waste in China. The diffusion behavior of HTO and Se(IV) in Tamusu clay rock was studied by through-diffusion (TD) experiments and numerical analysis to determine the spatial and temporal variation. A minimum error analysis was conducted to determine the HTO and Se(IV) diffusion coefficients in compacted TMS clay. The TD experimental results and numerical analysis showed that the diffusion of HTO and Se reached a steady state within 7 and 50 days, respectively, and the apparent diffusion coefficients (Da) decreased with the increases in the compacted density. In fact, there was retardation of Se diffusion in intact TMS clay rock. A two-site sorption model for Se was applied to simulate fast and slow sorption behavior quantitatively.
Advection-dispersion experiments (ADE) were effectively designed for inadequate transport models through a calibration/validation process. HTO, selenium (Se), and cesium (Cs) transport in crushed granite were studied using a highly reliable, dynamic column device in order to obtain the retardation factors (R) and the dispersion coefficients (D) by fitting experimental breakthrough curves (BTCs) for various path lengths. In order to conduct a safety assessment (SA) of a deep geological repository for high-level radioactive waste, radionuclide transport in rock systems is necessary to clarify and establish a suitable model. A dynamic column with a radiotracer (HTO, Se(IV), and Cs) was applied to 2, 4, and 8 cm path lengths using a STANMOD simulation. The results showed similar results between the BTCs of Se and Cs by fitting a non-equilibrium sorption model due to the retardation effect. In fact, there was a relatively obvious sorption of Se and Cs in the BTCs obtained by fitting a retardation factor (R) value higher than 1. In addition, a two-region (physical) and a two-site (chemical) non-equilibrium model with either the lowest sum of squared residuals (SSQ) or the root mean square error (RMSE) were applied to determine the Se and Cs sorption mechanisms on granite.
Various numerical methods have been being extensively used to estimate the diffusion parameters of pertechnetate (99TcO4−) in compacted MX80 bentonite clay using through-diffusion (TD) techniques. In this study, an improved TD column test was applied, and the diffusion fluxes of tritium (HTO) as a non-reactive radionuclide, and 99TcO4− with various dry densities, were compared under the same experimental conditions. Similar results were obtained for the apparent diffusion coefficients of HTO and 99TcO4− using three estimation methods: a graphical method applying the asymptote calculation, an analytical solution using Lsqcurvefit installed in MATLAB, and the Marquardt–Levenberg optimization algorithm in the HYDRUS-1D inverse method. The statistical analysis showed that the densities using a one-way analysis of variance (ANOVA) for the three estimation methods ranged from 1200 to 2000 kg/m3, which indicated that there were no obvious differences between HTO and 99TcO4−. In general, the diffusion parameters of 99TcO4− were lower than those for HTO due to anion exclusion effects and lower accessible porosity.