The FeCoNiCrMo_0.5Al_x system with x up to 2.13 was analyzed from the point of view of evolution of the phase composition and microstructure. Cast samples were synthesized by induction melting and analyzed by X-ray diffraction, energy dispersive spectroscopy, scanning electron microscopy, and Vickers microhardness test methods. Phase compositions of these alloys in dependance on Al concentration consist of FCC solid solution, σ-phase, NiAl-based B2 phase, and BCC solid solution enriched with Mo and Cr. Phase formation principles were studied. Al dissolves in a FeCoNiCrMo_0.5 FCC solid solution up to 8 at.%.; at higher concentrations, Al attracts Ni, removing it from FCC solid solution and forming the B2 phase. Despite Al not participating in σ-phase formation, an increase in Al concentration to about 20 at.% leads to a growth in the σ-phase fraction. The increase in the σ-phase was caused by an increase in the amount of B2 because the solubility of σ-forming Mo and Cr in B2 was less than that in the FCC solution. A further increase in Al concentration led to an excess of Mo and Cr in the solution, which formed a disordered BCC solid solution. The hardness of the alloys attained the maximum of 630 HV at 22 and 32 at.% Al.

Triboelectric nanogenerators (TENGs), as novel electronic devices for converting mechanical energy into electrical energy, are better suited as signal-testing sensors or as components within larger wearable Internet of Things (IoT) or Artificial Intelligence (AI) systems, where they handle small-device power supply and signal acquisition. Consequently, TENGs hold promising applications in self-powered sensor technology. As global energy supplies become increasingly tight, research into self-powered sensors has become critical. This study presents a self-powered sport sensor system utilizing a triboelectric nanogenerator (TENG), which incorporates a thermoplastic polyurethane (TPU) film doped with graphene and polytetrafluoroethylene (PTFE) as friction materials. The graphene-doped TPU nanocomposite film-based TENG (GT-TENG) demonstrates excellent working durability. Furthermore, the GT-TENG not only consistently powers an LED but also supplies energy to a sports timer and an electronic watch. It serves additionally as a self-powered sensor for monitoring human movement. The design of this self-powered motion sensor system effectively harnesses human kinetic energy, integrating it seamlessly with sport sensing capabilities.

In this work, we studied the influence of the geometry and degree of filling of glass dispersed particles on the optical and mechanical properties of flexible high-transmission composites, based on thermoplastic polyurethane. Glass spheres, glass flake and milling glass fiber were used as fillers. Studies of mechanical properties have shown that the introduction of any filler leads to a decrease in tensile strength and an increase in the elastic modulus of the composite material, however, with the introduction of glass flakes and milling glass fiber, a significant increase in the yield strength of the material is observed. The optical properties of composites with glass spheres decrease exponentially with an increase in the volume fraction of the filler. With an increase in the concentration of glass flakes and milling glass fiber to 10 vol.%, a sharp decrease in transmission is observed. With a further increase in concentration, the orientation of the filler along the film occurs, due to which the transmission in the visible range increases to values close to those of a pure polymer.

The pursuit of eco-friendly and renewable power generation has driven technological breakthroughs in nanoscale engineering, particularly regarding triboelectric nanogenerators (TENGs). These devices have become a focus of interest due to their capacity to effectively transform kinetic energy into electrical power via combined triboelectrification and electrostatic charge separation mechanisms. TENGs now find expanding implementations across multiple fields including in flexible electronics, autonomous sensing systems, and ambient energy conversion technologies. Enhancing TENG performance critically depends on the strategic design and application of nanostructures and nanomaterials. Nonetheless, challenges such as material selection, compatibility, homogeneous dispersion, interfacial stability, and production scalability must be overcome to advance TENG technology. Moreover, the mechanisms by which nanomaterials contribute to the triboelectric effect remain insufficiently understood, underscoring the necessity for systematic theoretical models. This review provides a comprehensive overview of recent advancements in integrating nanostructures and nanomaterials into TENGs, elucidating their roles, advantages, and underlying mechanisms in enhancing energy conversion efficiency, while identifying key challenges and proposing future research directions.