The worlds progression towards the Hydrogen economy is facilitating the production of hydrogen from various resources. In the carbon based hydrogen production, Water gas shift reaction is the intermediate step used for hydrogen enrichment and CO reduction in the synthesis gas. This paper makes a critical review of the developments in the modeling approaches of the reaction for use in designing and simulating the water gas shift reactor. Considering the fact that the rate of the reaction is dependent on various parameters including the composition of the catalyst, the active surface and structure of the catalyst, the size of the catalyst, age of the catalyst, its operating temperature and pressure and the composition of the gases, it is difficult to narrow down the expression for the shift reaction. With different authors conducting experiments still to validate the kinetic expressions for the shift reaction, continuous research on different composition and new catalysts are also reported periodically. Moreover the commercial catalyst manufacturers seldom provide information on the catalyst. This makes the task of designers difficult to model the shift reaction. This review provides a consolidated listing of the various important kinetic expressions published for both the high temperature and the low temperature water gas shift reaction along with the details of the catalysts and the operating conditions at which they have been validated.
The present study deals with the determination of physical and chemical parameters in the treatment process of waste water by flocculation and coagulation processes using natural coagulants and assessing their feasibility for water treatment by comparing the performance with each other and with a synthetic coagulant. Initial studies were done on the synthetic waste water to determine the optimal pH and dosage, the activity of natural coagulant, followed by the real effluent from tannery waste. The raw tannery effluent was bluish-black in colour, mildly basic in nature, with high COD 4000mg/l and turbidity in the range 700NTU, was diluted and dosed with organic coagulants, AloeVera, MoringaOleifera and Cactus (O.ficus-indica).. The study observed that coagulant Moringa Oleifera of 15 mg/L dose at 6 pH gave the best reduction efficiencies for major physicochemical parameters followed by Aloe Vera and Cactus under identical conditions. The study reveals that the untreated tannery effluents can be treated with environmental confirmative naturally occurring coagulants.
1 March 2015 in Brazilian Journal of Chemical Engineering
In this study polyethersulfone ultrafiltration membrane were prepared with the modifier gelatin at 0, 5, 10, 15 and 20 wt % using DMF as solvent by phase inversion process. Morphologies and characteristics of the membranes were investigated through the methods of SEM, XRD, contact angle measurements. The performance of the modified membrane for the treatment of leather and distillery wastewater through a deadend ultrafiltration process was studied. Morphological investigation showed that the 10% gelatin content in 90% PES results in a two layer structure with a porous top and homogeneous sub-layer with uniform number of pores on the surface. The pure water flux of the modified membrane increases with gelatin concentration, which results in better permeation for both leather and distillery wastewater. In addition to 80-90% reduction in BOD and COD, all modified PES UF membranes showed moderate removal of total suspended and dissolved solids, chlorides, sulphate, oil and grease, potassium, sodium and ammonical nitrogen, apart from color removal.
1 December 2017 in Resource-Efficient Technologies
The present study aims at finding out the optimum parameters for the extraction of components from Betel leaves possessing medicinal applications using ethanol solvent by Soxhlet apparatus. The optimum conditions for the extract were calculated based on the extract yield by varying four parameters: material quantity (A: 2â4âg), solvent quantity (B: 250â300âml), mantle temperature (C: 65â75 °C) and extraction time (D: 1â3 hours) and optimized using a four factor three level BoxâBehnken response surface design (BBD) coupled with desirability function methodology. Results showed that temperature and extraction time had significant effect on yield of extract. Optimum conditions for highest yield of extract (10.94%) are as follows: material quantity (2âg), solvent quantity (281.4âml), temperature (72 °C) and time (3 hours). The extract at the maximum yield condition was analyzed for phytocomponents by FTIR and GCâMS. The results indicated the presence of Hydroxy chavicol (69.46%), 4-Chromanol (24%) and Eugenol (4.86%), which possess wide application including as antioxidant, anti-inflammatory, anti-platelet and antithrombotic, antibacterial and antifungal agents. Keywords: Betel leaves, BoxâBehnken response surface design (BBD), Phytocomponents, Antioxidant
17 July 2025 in Chemical Engineering Journal Advances