As the distribution function of traffic load effect on bridge structures has always been unknown or very complicated, a probability model of extreme traffic load effect during service periods has not yet been perfectly predicted by the traditional extreme value theory. Here, we focus on this problem and introduce a novel method based on the bridge structural health monitoring data. The method was based on the fact that the tails of the probability distribution governed the behavior of extreme values. The generalized Pareto distribution was applied to model the tail distribution of traffic load effect using the peak-over-threshold method, while the filtered Poisson process was used to model the traffic load effect stochastic process. The parameters of the extreme value distribution of traffic load effect during a service period could be determined by theoretical derivation if the parameters of tail distribution were estimated. Moreover, Bayes’ theorem was applied to update the distribution model to reduce the statistical uncertainty. Finally, the rationality of the proposed method was applied to analyze the monitoring data of concrete-filled steel tube arch bridge suspenders. The results proved that the approach was convenient and found that the extreme value distribution type III might be more suitable as the traffic load effect probability model.
10 January 2025 in Measurement Science and Technology
Cables are the primary load-bearing component of cable-stayed bridges, the accurate monitoring of cable tension is essential for evaluating cable service reliability and bridge safety. Addressing the challenges faced by existing vision monitoring technologies in complex environments, such as limited camera resolution, low-light conditions, adverse weather and camera vibration, a non-contact vision-based monitoring system based on computer vision technology has been developed and applied to cable tension monitoring in cable-stayed bridges. The monitoring system addresses the challenges under low-light and adverse weather by utilizing an industrial camera equipped with an infrared filter and an infrared light source. A sub-pixel template matching algorithm is employed to enhance measurement accuracy under limited resolution. Furthermore, a camera vibration cancellation algorithm is introduced to mitigate the impact of external vibrations, significantly improving measurement stability. Both model experiments and field test were conducted to validate the monitoring system. Results from the model experiments demonstrate high measurement accuracy and stability under limited resolution, low-light, and adverse weather, with a maximum frequency recognition error of only 0.4%. The field test further demonstrates a significant improvement in measurement accuracy through the camera vibration cancellation method, achieving a cable tension error of only 0.86% compared to the design tension. These results highlight the system’s potential for reliable cable tension monitoring in complex environments.
6 September 2022 in Measurement Science and Technology
The problem of effective information extraction of dynamic signals is a key challenge of vibration-based structural health monitoring. Traditional ensemble empirical mode decomposition (EEMD) and complementary EEMD (CEEMD) are effective filtering methods but have the shortcomings of mode mixing, completeness and the endpoint effect in adaptive decomposition stage. To address the above problems, this paper proposes a noise mode identification method based on multiscale local pattern filtering with a machine learning algorithm. In addition, this method improves the filtering performance of mode decomposition and wavelet threshold denoising methods effectively. To validate the performance of this method, simulation experiment and real signal analysis were used for validation: their results showed that the proposed method has better adaptive decomposition performance than EEMD and CEEMD. Compared with the EEMD, CEEMD and wavelet threshold denoising methods, the proposed method can better balance smoothness and the power reserve, has optimized time- and frequency-domain characteristics, filters with a higher signal-to-noise ratio and reliability, and has more optimized filtering performance. The method proposed in this paper can be applied to bridge health monitoring technology, and has important scientific and engineering significance.
31 December 2021 in Environmental and Earth Sciences Research Journal
Aiming at the serious noise of bridge vibration signals in complex environment, this paper proposed an adaptive filtering and denoising optimization method for bridge structural health monitoring. The method took CEEMDAN algorithm as the core, during the step-by-step decomposition of original signals, white noise with opposite signs was added in each stage, meanwhile multi-scale permutation entropy (MPE) was introduced to analyze the mean entropy of each intrinsic mode function (IMF) at different scales, and components with serious noise were eliminated to complete the first filtering; then, in order to optimize the remaining IMFs for signal reconstruction and ensuring the smoothness and similarity of filtering, an optimized reconstruction model was established to complete the second filtering. Compared with the CEEMDAN method, the proposed method could solve the problems of mode mixing and endpoint effect with good completeness, orthogonality, and signal-to-noise ratio. At last, the advantages and application value of the proposed method were verified again by the vibration signal analysis of a real long-span bridge structure.