Ahmed Hayali

Dr. Ahmed Hayali

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 November 2021 in EPJ Photovoltaics
Verified
Journal Article
Open access
PDF file
Ahmed HayaliAhmed Hayali
Ahmed Hayali
MAMaan M. Alkaisi
Maan M. Alkaisi
High conductivity and transparency of the electron-transporting layer (ETL) is essential to achieve high efficiency perovskite solar cells (PvSCs). Generally, titanium dioxide (TiO2) has been extensively utilized as an ETL in PvSCs. Both surface roughness and uniformity of the compact-TiO2 (C-TiO2) can influence the efficiency of the PvSC. This work investigates the optimization of the direct current (DC) sputtering power and the ratio of argon (Ar) to oxygen (O2) plasma to achieve high quality ETL films. The effect of changing the DC sputtering power on the C-TiO2 films and subsequently on the overall efficiency was studied. The electrical and optical properties of the C-TiO2 layer were characterized for various DC powers and different ratios of Ar to O2 plasma. It was found that the optimum preparation conditions for the C-TiO2 films were obtained when the DC power was set at 200 W and a flow rate of 6 sccm Ar and 12 sccm O2. A power conversion efficiency (PCE) of 15.3% in forward sweep and 16.7% in reverse sweep were achieved under sunlight simulator of 100 mW/cm2. These results indicate that significant improvement in the efficiency can be achieved, by optimizing the C-TiO2 layer.

28 May 2025 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Ahmed HayaliAhmed Hayali
Ahmed Hayali
MAMaan Alkaisi
Maan Alkaisi
Tin oxide (SnO2) is an attractive candidate for the electron transport layer (ETL) in perovskite-based solar cells because of its low temperature process requirement. The ability to form ETL layers at low temperatures opens up opportunities for the use of flexible and low-cost materials suitable for photovoltaic applications. The ETL is necessary for the extraction of electrons and charge separation from the perovskite active layer. Herein, we present a study of the effect of annealing temperature on SnO2 used as an ETL. The annealing temperature of the SnO2 has a considerable effect on the morphology, crystallinity, grain size, and surface topography of the SnO2 layer. The surface properties of the ETL influence the structural properties of the perovskite films. In this study, the annealing temperature of the SnO2, deposited using spin coating, was changed from 90 °C to 150 °C. The SnO2 films annealed at 120 °C resulted in reduced surface defects, improved electron extraction, and produced a significant increase in the grain size of the perovskite active layers. The increase in grain size led to improved efficiency of the PSCs. Devices annealed at 120 °C yielded PSCs with an average efficiency of 15% for a 0.36 cm2 active area, while devices treated at 90 °C and 150 °C produced an average efficiency of 12%. The PSCs fabricated at low temperatures provide an effective technique for low-cost manufacturing, especially on flexible and polymer-based substrates.

22 September 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
Ahmed HayaliAhmed Hayali
Ahmed Hayali
RRRoger J. Reeves
Roger J. Reeves
MAMaan Alkaisi
Maan Alkaisi
Perovskite materials offer high-efficiency low-cost solar cells and applications versatility. We report on cesium-based hybrid perovskite solar cells with wavelength-selective properties ranging from 500 nm (UV-VIS) to 800 nm (IR). The band gap tuning was achieved through composition changes of mainly lead(II) iodide PbI2 and lead(II) bromide PbBr2. The optical spectra of the developed materials were studied, including the photoluminescence (PL), optical transparency, X-ray diffraction and external quantum efficiency for samples prepared under different compositions. It was found that a high content of iodine displayed a photoluminescence (PL) peak at 790 nm, whereas a high content of bromine showed a PL peak at 548 nm. The combined composition mixture of PbI2 and PbBr2 can be fine-tuned to prepare materials that absorbed light in the visible range (640–660 nm) or other selective wavelengths in the range from 500 to 800 nm. The illuminated current-voltage characteristics of the solar cells were carried out under the AM 1.5 condition using an ABET solar simulator with a reference solar cell for comparison and control. The average efficiency of the fabricated solar cells ranged from 3.5% to 15.5%, depending on perovskite composition. Wavelength-selective solar cells have potential applications in smart windows, building of integrated PVs and solar-operated greenhouses.

19 September 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Ahmed HayaliAhmed Hayali
Ahmed Hayali
RRRoger J. Reeves
Roger J. Reeves
MAMaan Alkaisi
Maan Alkaisi
The efficiency and stability of perovskite solar cells (PSCs) depend not only on the perovskite film quality, but they are also influenced by the charge carriers of both the electron and hole transport layers (ETL and HTL). Doping of the carrier transport layers is considered one of effective technique applied to enhance the efficiency and performance of the PSCs. FK209 cobalt TFSI and lithium TFSI salt were investigated as dopants for mesoporous TiO2 (M-TiO2) in the ETL. Herein, FK209 cobalt doping offers improved conductivity, reproducibility and stability compared to other doping or undoped M-TiO2 control device. It has been found that an optimum concentration of 2.5 mg FK209 cobalt in the M-TiO2 has resulted in an efficiency of 15.6% on 0.36 cm2 active device area, whereas, the undoped M-TiO2 yielded an average efficiency of 10.8%. The enhanced efficiency is due to the improved conductivity of the ETL while maintaining high transparency and low surface roughness with FK209 doping. The M-TiO2 doped with FK209 has a transparency of the 90% over the visible range and its measured energy gap was 3.59 eV. Perovskite films deposited on the M-TiO2 doped with FK209 has also a lower PL intensity indicating faster charge extraction. The measured lifetime of the perovskite films deposited on the optimised M-TiO2 film was 115.8 ns.

8 August 2024 in Inorganics
Verified
Journal Article
Open access
PDF file
Ahmed HayaliAhmed Hayali
Ahmed Hayali
MAMaan Alkaisi
Maan Alkaisi
Perovskite solar cells (PSCs) have demonstrated remarkable progress in performance in recent years, which has placed perovskite materials as the leading promising materials for future renewable energy applications. The solvent additive technique in perovskite composition is a simple but effective process used to improve the surface quality of the perovskite layers and to improve the performance and charge transport processes essential to the functions of PSCs. These additives can have a considerable effect on the topography, crystallinity, and surface properties of the perovskite active layer, ultimately influencing the stability of the PSCs. A “two-step spin coating” deposition method to make PSCs in ambient air laboratory conditions was employed. Acetonitrile (ACN) was conventionally utilized as a chemical additive to enhance the performance of PSCs. In this study, our film properties exhibited that the incorporation of ACN in the triple cation perovskite precursor led to the passivation of surface defects and a noticeable increase in the size of the crystal grains of the perovskite films, which led to enhanced stability of devices. The efficiency achieved for PSCs prepared with 10% ACN was 15.35%, which is 30% higher than devices prepared without ACN. In addition, devices prepared with ACN have shown a lower hysteresis index and more stable behavior compared to devices prepared without ACN. This work presents an easy, low-cost method for the fabrication of high performance PSCs prepared under ambient air laboratory conditions.

20 June 2021
Verified
Conference Paper
Closed access
Ahmed HayaliAhmed Hayali
Ahmed Hayali
MAMaan M. Alkaisi
Maan M. Alkaisi
Solvents play an important role in the preparation of the electron ETL and hole HTL transport layers and consequently in determining the optical properties, morphologies and perovskite thin-film quality. Lithium TFSI employed in HTL and FK209 cobalt TFSI used in ETL are usually dissolved by acetonitrile (ACN) solvent. However, this solvent is toxic and can accelerate the deterioration of the perovskite films. This work propose alternatives for ACN to slow down the perovskite films deterioration and improve its performance. Solar cells prepared using FK209/ethanol and lithium/isopropanol alcohol have shown excellent performance with champion device efficiency reaching 23.5%.