Cheng Wang

Dr. Cheng Wang


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 September 2021 in Metals
Verified
Journal Article
Open access
PDF file
JZJin Zhang
Jin Zhang
WTWenfu Tan
Wenfu Tan
CWCheng Wang
Cheng Wang
CZChunnan Zhu
Chunnan Zhu
YYyouping yi
youping yi
Cryogenic deformation can improve the strength and plasticity of Al–Li alloy, although the underlying mechanism is still not yet well understood. The effects of cryogenic temperature on the tensile properties and microstructure of an Al–Cu–Li alloy were investigated by means of tensile property test, roughness measurement, scanning electron microscope (SEM), optical microscope (OM), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The results indicated that the strength and elongation of the as-annealed (O-state) and solution-treated (W-state) alloys increased with the decrease in deformation temperature, where the increasing trend of elongation of the W-state alloy was more significant than that of the O-state alloy. In addition, a temperature range was observed at approximately 178 K that caused the strength of the W-state alloy to slightly decrease. The decrease in temperature inhibited the dynamic recovery of the Al–Cu–Li alloy, which increased the dislocation density and the degree of work hardening, thus improving the strength of the alloy. At cryogenic temperatures, the internal grain structure was more involved in the deformation and the overall deformation was more uniform, which caused the alloy to have higher plasticity. This study provides a theoretical basis for the cryogenic forming of Al–Li alloy.

27 August 2021 in Materials
Verified
Journal Article
Open access
PDF file
CWCheng Wang
Cheng Wang
JZJin Zhang
Jin Zhang
YYyouping yi
youping yi
CZChunnan Zhu
Chunnan Zhu
The mechanical properties of Al-Cu-Li alloys after different pretreatments were investigated through tensile testing at 25 and −196 °C, and the corresponding microstructure characteristics were obtained through optical metallography, scanning electron microscopy, electron backscatter diffraction, and transmission electron microscopy. An increasing mechanism of both strength and ductility at cryogenic temperatures was revealed. The results show that the hot deformation pretreatment before homogenization promoted the precipitation of Al3Zr particles, improved particle distribution, and inhibited local precipitation-free zones (PFZ). Both hot deformation pretreatment before homogenization and cryogenic temperature were able to improve strength and ductility. The former improved strength by promoting the precipitation of Al3Zr particles while enhancing the strengthening effect of the second-phase particles and reducing the thickness of the coarse-grained layer. Meanwhile, the increase in ductility is attributable to the decrease in thickness of the coarse-grained layer, which reduced the deformation incompatibility between the coarse and fine grains and increased the strain-hardening index. The latter improved the strength by suppressing dynamic recovery during the deformation process, increasing the dislocation density, and enhancing the work hardening effect. Additionally, the increase in ductility is attributable to the suppression of planar slip and strengthening of grain boundaries, which promoted the deformation in grain interiors and made the deformation more uniform.

27 October 2020 in Materials
Verified
Journal Article
Open access
PDF file
HGHui Guo
Hui Guo
CWCheng Wang
Cheng Wang
JZJin Zhang
Jin Zhang
YDYunlai Deng
Yunlai Deng
The effects of Zn and Mg content in thin-walled square extrusions of Al-Zn-Mg alloys on its crashworthiness were investigated, and the correlation between the crushing properties, mechanical properties, and microstructures of the profiles were investigated. The results showed that the strength and the compression properties were gradually increased with a decrease in the Zn/Mg ratios (from 12.48 to 4.57). When the Zn/Mg ratio is lower (less than 6.29), an increase in the Mg content simultaneously improves the alloy strength and the compression properties. An increase in Zn content (from 5.07 to 6.77) can improve the strength of the alloy however, it does not affect the compression properties. However, the higher Zn contents (6.77%) would lead to cracking in advance during the compressing, which reduces the compression energy absorption capacities of the product. Therefore, in order to obtain higher strength and excellent compression properties, the Zn/Mg ratio should be reduced. For the upper limit, the Zn content should not be too high (less than 6.77), as this may lead to early cracking and failure. For the lower limit, the Mg content should be higher (more than 0.91) to make sure that the alloy has excellent compression properties and higher strength.

15 February 2022 in Frontiers in Materials
Verified
Journal Article
Open access
JZJin Zhang
Jin Zhang
HZHuaqiang Zeng
Huaqiang Zeng
CWCheng Wang
Cheng Wang
ZTZibo Tang
Zibo Tang
The regulation of blank microstructure is the key to manufacturing high-quality ring cylinder by composite spinning - extrusion forming. In this paper, the precipitation morphologies of three Al3Zr dispersions were obtained by changing the heat treatment process, and their effects on the microstructure and mechanical properties of Al-Cu-Li alloy ring cylinder were investigated. The results show that the microstructure and mechanical properties of ring cylinder are affected by the different precipitation distribution of Al3Zr dispersoids in the blank. When the Al3Zr dispersoids precipitated and dispersed, the cracking of ring cylinder was eliminated, the thickness of coarse-grained layer decreases obviously, and the elongation is increased by 33.5%. In the T83 state, the average length of the T1 phase decreased from 100.3 to 77.5 nm, while the tensile strength and yield strength of ring cylinder increased by 16 and 20 MPa, respectively.

5 November 2021 in Metals and Materials International
Verified
Journal Article
Closed access
PDF file
HGHui Guo
Hui Guo
JZJin Zhang
Jin Zhang
CWCheng Wang
Cheng Wang
YDYun-Lai Deng
Yun-Lai Deng