YAO Xingxing

Mr. YAO Xingxing


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 December 2023 in European Journal of Physics
Verified
Journal Article
Closed access
YXYAO Xingxing
YAO Xingxing
LGLiu Gongyu
Liu Gongyu
YHYang Hancheng
Yang Hancheng
XTXiao Ting
Xiao Ting
ZYZheng Yuan
Zheng Yuan
A washer on a vertical steel rod may start spinning instead of simply sliding down. The forces on the washer are analyzed, and the relationship between the angular velocity of rotation and the angular velocity of precession is obtained. A relationship about the coefficient of friction of the washer is obtained at the condition of rotation without slipping. The influence of the coefficient of friction and the ratio of the inner diameter of the washer to the diameter of the rod on the sliding state was investigated experimentally, and a two-dimensional phase diagram of the rotation without slipping was obtained. The relationship between the three parameters(the nutation angle of the washer, the angular velocity of precession, and the final vertical velocity) and the ratio of the inner diameter of the washer to the diameter of the rod in the condition of rotation without slipping was further investigated. The experimental results are in good agreement with the theoretical equations.

1 January 2025 in The Physics Teacher
Verified
Journal Article
Closed access
PDF file
TXTing Xiao
Ting Xiao
YXYAO Xingxing
YAO Xingxing
YZYuan Zheng
Yuan Zheng
Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b Reflection is a very common daily phenomenon. Except for light sources, we see almost everything by reflection. A large amount of information about objects is b

10 May 2023 in European Journal of Physics
Verified
Journal Article
Closed access
YXYAO Xingxing
YAO Xingxing
ZWZi-Wen Wang
Zi-Wen Wang
LZLiang-Liang Zhao
Liang-Liang Zhao
YZYuan Zheng
Yuan Zheng
The bouncing process of an irregular object falling on the ground contains many interesting mechanical problems. The article investigated the bounce height of a capsule-shaped object when it falls on the ground. The variation of three physical quantities, namely the angle of the object, the linear velocity of the center of mass and the angular velocity relative to the center of mass when it fell on the ground are studied. According to the limit condition of friction, the three-dimensional phase diagram of the above three physical quantities was drawn when the fall height of the capsule-shaped object and the bounce height was equal. The movement of the capsule-shaped object is captured by using two cameras positioned perpendicular to each other. The trajectory was tracked by TRACKER software to obtain the fall height and bounce height of the capsule. When the bounce height was higher than the fall height, it was marked with a red dot. If both heights were equal, it was marked with a black dot. Otherwise, it was marked with a blue dot. Different types of experimental data points are plotted in the phase diagram. A large amount of random experimental data verifies the correctness of the theory.

1 October 2022 in Materials Research Express
Verified
Journal Article
Open access
YXYAO Xingxing
YAO Xingxing
JFJia-Chen Feng
Jia-Chen Feng
A short metal wire can be used as a fuse in a circuit. Using ANSYS software simulations combined with experiments, it was verified that the highest temperature region during the blowing process of the wire and the most blowing position is near the middle When a direct current flow through. A measurement circuit was established to study the effect of fuse length, and current on fuse blowing time. The results show that for 0.05 mm diameter copper wire, the blowing time decreases rapidly with the increase of length when the length is within 1cm under the action of 3.16A direct current, and the blowing time is basically stable at 0.04s when the length exceeds 1 cm due to the limitation of heat transfer distance. The blowing time of copper wire decreases with the increase of current, and the blowing time is basically stable at 0.05s after the current reaches 3.5A; the melting time of three materials (Cu, Ag, Pb-Sb) all satisfy the theoretical prediction that the product of current density squared and time is constant; the equivalent current density is introduced to modify the theoretical formula, which makes the theory and experiment more in agreement. This study provides a more comprehensive description of the blowing time and characteristics of short metal wires under the action of high current (DC) from both theoretical and experimental aspects.

8 August 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
YXYAO Xingxing
YAO Xingxing
FSFanhao Shen
Fanhao Shen
YZYuan Zheng
Yuan Zheng
TXTing Xiao
Ting Xiao
The hot wire anemometer is a commonly used device for measuring air speed in laboratories. In this paper, the relationship between air speed and the hot wire temperature in different air speed ranges was analyzed based on the theory of thermal equilibrium. A measurement circuit and hot wire shape were designed based on the principle of the hot wire anemometer, and the linear relationship between current and temperature in the hot wire at different air speeds was verified in an adjustable air speed field. The measured current was used to represent air speed. The designed hot wire anemometer was experimentally validated to provide measurement results that match the theoretical values in different air speed ranges. Finally, the sensitivity of the anemometer in different measurement ranges was determined based on the uncertainty of the instrument's sensitivity and the measurement formula.

8 July 2026 in European Journal of Physics
Verified
Journal Article
Closed access
TXTing Xiao
Ting Xiao
XTXintao Tian
Xintao Tian
YZYuan Zheng
Yuan Zheng
YXYAO Xingxing
YAO Xingxing
BYBo Yang
Bo Yang
This study presents the design and analysis of a self-assembled, triangular straw-based centrifugal pump. A combined theoretical and experimental approach was employed to systematically investigate its pumping mechanism and performance. The effects of key geometric parameters—tube length, inner diameter, and inclination angle—along with the rotational angular velocity on the volumetric flow rate were quantified. The theoretical framework integrates centrifugal force dynamics, Bernoulli’s principle, and a comprehensive fluid resistance model accounting for both frictional and local losses. Experimental validation was performed using a custom-built apparatus equipped with a precision rotation control system and a flow measurement setup, testing a series of 3D-printed straw specimens with varying dimensions. The results indicate that the flow rate increases with angular velocity and the square of the tube diameter, shows an approximate linear dependence on tube length, and requires exceeding a critical angular velocity for pump initiation. This work establishes a predictive model and provides empirical data to guide the design and optimization of such low-cost, easily fabricated micro-scale pumping devices.