Hamad Alharbi

Dr. Hamad Alharbi

orcid

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 January 2020 in Scientific Reports
Verified
Journal Article
Open access
PDF file
Md Khan Sobayel Bin RafiqMd Khan Sobayel Bin Rafiq
Md Khan Sobayel Bin Rafiq
Nowshad AminNowshad Amin
Nowshad Amin
HAHamad Alharbi
Hamad Alharbi
MMMonis Luqman Mohammed
Monis Luqman Mohammed
AAAfida Ayob
Afida Ayob
MAMd. Akhtar Akhtaruzzaman
Md. Akhtar Akhtaruzzaman
Radio frequency (RF) magnetron sputtering was used to deposit tungsten disulfide (WS2) thin films on top of soda lime glass substrates. The deposition power of RF magnetron sputtering varied at 50, 100, 150, 200, and 250 W to investigate the impact on film characteristics and determine the optimized conditions for suitable application in thin-film solar cells. Morphological, structural, and opto-electronic properties of as-grown films were investigated and analyzed for different deposition powers. All the WS2 films exhibited granular morphology and consisted of a rhombohedral phase with a strong preferential orientation toward the (101) crystal plane. Polycrystalline ultra-thin WS2 films with bandgap of 2.2 eV, carrier concentration of 1.01 × 1019 cm−3, and resistivity of 0.135 Ω-cm were successfully achieved at RF deposition power of 200 W. The optimized WS2 thin film was successfully incorporated as a window layer for the first time in CdTe/WS2 solar cell. Initial investigations revealed that the newly incorporated WS2 window layer in CdTe solar cell demonstrated photovoltaic conversion efficiency of 1.2% with Voc of 379 mV, Jsc of 11.5 mA/cm2, and FF of 27.1%. This study paves the way for WS2 thin film as a potential window layer to be used in thin-film solar cells.

5 January 2021 in Membranes
Verified
Journal Article
Open access
PDF file
SNSAAD NAUMAN
SAAD NAUMAN
GLGilles Lubineau
Gilles Lubineau
HAHamad Alharbi
Hamad Alharbi
Electrospinning is a versatile technique which results in the formation of a fine web of fibers. The mechanical properties of electrospun fibers depend on the choice of solution constituents, processing parameters, environmental conditions, and collector design. Once electrospun, the fibrous web has little mechanical integrity and needs post fabrication treatments for enhancing its mechanical properties. The treatment strategies include both the chemical and physical techniques. The effect of these post fabrication treatments on the properties of electrospun membranes can be assessed through either conducting tests on extracted single fiber specimens or macro scale testing on membrane specimens. The latter scenario is more common in the literature due to its simplicity and low cost. In this review, a detailed literature survey of post fabrication strength enhancement strategies adopted for electrospun membranes has been presented. For optimum effect, enhancement strategies have to be implemented without significant loss to fiber morphology even though fiber diameters, porosity, and pore tortuosity are usually affected. A discussion of these treatments on fiber crystallinity, diameters, and mechanical properties has also been produced. The choice of a particular post fabrication strength enhancement strategy is dictated by the application area intended for the membrane system and permissible changes to the initial fibrous morphology.

1 March 2015 in International Journal of Plasticity
Verified
Journal Article
Closed access
HAHamad Alharbi
Hamad Alharbi
SKSurya Kalidindi
Surya Kalidindi

18 November 2018 in Journal of Applied Polymer Science
Verified
Journal Article
Closed access
PDF file
MHMustafa Y. Haddad
Mustafa Y. Haddad
HAHamad Alharbi
Hamad Alharbi

19 March 2020 in Coatings
Verified
Journal Article
Open access
PDF file
HAHamad Alharbi
Hamad Alharbi
MHMustafa Y. Haddad
Mustafa Y. Haddad
Muhammad Omer AijazMuhammad Omer Aijaz
Muhammad Omer Aijaz
AAAbdulaziz Assaifan
Abdulaziz Assaifan
Mohammad Rezaul KarimMohammad Rezaul Karim
Mohammad Rezaul Karim
Bilayer nanofiber membranes with enhanced adsorption and mechanical properties were produced by combining a layer of polyacrylonitrile (PAN) functionalized with metal oxides (MO) of ZnO or TiO2 with a layer of chitosan (CS) via consecutive electrospinning. The adsorption properties of the bilayer PAN/MO–CS nanofiber membranes against lead (Pb(II)) and cadmium (Cd(II)) ions were investigated, including the effects of the solution pH, initial ion concentrations, and interaction time. The integration of a CS layer into PAN/MO nanofibers increased the adsorption capacity of lead by 102% and cadmium by 405%, compared to PAN/MO single layer. The nonlinear optimization method showed that the pseudo-second-order kinetic model and Langmuir isotherm equation better described the adsorption results. More importantly, the incorporation of a supportive CS nanofiber layer enhanced the tensile strength of PAN/MO–CS bilayer by approximately 68% compared to the PAN/MO single layer, owing to the strong interaction between the fibers at the interface of the two layers.

15 September 2018 in Journal of Polymer Research
Verified
Journal Article
Closed access
PDF file
MHMustafa Y. Haddad
Mustafa Y. Haddad
HAHamad Alharbi
Hamad Alharbi
Mohammad Rezaul KarimMohammad Rezaul Karim
Mohammad Rezaul Karim
Muhammad Omer AijazMuhammad Omer Aijaz
Muhammad Omer Aijaz
NANabeel H. Alharthi
Nabeel H. Alharthi