Matija Jezersek

Prof. Matija Jezersek

University of Ljubljana, Faculty of Mechnical Engineering
orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
24 April 2015 in BioMedical Engineering OnLine
Verified
Journal Article
Open access
PDF file
UPUrban Pavlovčič
Urban Pavlovčič
JDJanez Diaci
Janez Diaci
JMJanez Možina
Janez Možina
Matija JezersekMatija Jezersek
Matija Jezersek
Wound measuring serves medical personnel as a tool to assess the effectiveness of a therapy and predict its outcome. Clinically used methods vary from measuring using rules and calipers to sophisticated methods, based on 3D measuring. Our method combines the added value of 3D measuring and well-known segmentation algorithms to enable volume calculation and achieve reliable and operator-independent analysis, as we demonstrate in the paper. Developed 3D measuring system is based on laser triangulation with simultaneous color acquisition. Wound shape analysis is based on the edge-determination, virtual healthy skin approximation over the wound and perimeter, area, and volume calculation. In order to validate the approach, eight operators analyzed four different wounds using proposed method. Measuring bias was assessed by comparing measured values with expected values on an artificially modeled set of wounds. Results indicate that the perimeter, area, and volume are measured with a repeatability of 2.5 mm, 12 mm2, and 30 mm3, respectively, and with a measuring bias of −0.2 mm, −8.6 mm2, 24 mm3, respectively. According to the results of verification and the fact that typical wound analysis takes 20 seconds, the method for wound shape measurement can be clinically used as a precise tool for objectively monitoring the wound healing based on measuring its 3D shape and color.

11 January 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
LHLuka Hribar
Luka Hribar
PGPeter Gregorcic
Peter Gregorcic
MSMatej Senegačnik
Matej Senegačnik
Matija JezersekMatija Jezersek
Matija Jezersek
In this paper, we investigate the influence of the following parameters: pulse duration, pulse repetition rate, line-to-line and pulse-to-pulse overlaps, and scanning strategy on the ablation of AISI 316L steel and CuZn37 brass with a nanosecond, 1064-nm, Yb fiber laser. The results show that the material removal rate (MRR) increases monotonically with pulse duration up to the characteristic repetition rate (f0) where pulse energy and average power are maximal. The maximum MRR is reached at a repetition rate that is equal or slightly higher as f0. The exact value depends on the correlation between the fluence of the laser pulses and the pulse repetition rate, as well as on the material properties of the sample. The results show that shielding of the laser beam by plasma and ejected material plays an important role in reducing the MRR. The surface roughness is mainly influenced by the line-to-line and the pulse-to-pulse overlaps, where larger overlap leads to lower roughness. Process optimization indicates that while operating with laser processing parameters resulting in the highest MRR, the best ratio between the MRR and surface roughness appears at ~50% overlap of the laser pulses, regardless of the material being processed.

10 May 2016 in International Journal of Thermophysics
Verified
Journal Article
Open access
PDF file
NLNejc Lukač
Nejc Lukač
PGPeter Gregorčič
Peter Gregorčič
Matija JezersekMatija Jezersek
Matija Jezersek
Laser-activated irrigation is a powerful endodontic treatment for smear layer, bacteria, and debris removal from the root canal. In this study, we use shadow photography and the laser-beam-transmission probe to examine the dynamics of laser-induced vapor bubbles inside a root canal model and compare ultrasonic needle irrigation to the laser method. Results confirm important phenomenological differences in the two endodontic methods with the laser method resulting in much deeper irrigation. Observations of simulated debris particles show liquid vorticity effects which in our opinion represents the major cleaning mechanism.

5 February 2015 in BMC Medical Imaging
Verified
Journal Article
Open access
PDF file
PPPrimož Poredoš
Primož Poredoš
DČDušan Čelan
Dušan Čelan
JMJanez Možina
Janez Možina
Matija JezersekMatija Jezersek
Matija Jezersek
The main objective of the present method was to automatically obtain a spatial curve of the thoracic and lumbar spine based on a 3D shape measurement of a human torso with developed scoliosis. Manual determination of the spine curve, which was based on palpation of the thoracic and lumbar spinous processes, was found to be an appropriate way to validate the method. Therefore a new, noninvasive, optical 3D method for human torso evaluation in medical practice is introduced. Twenty-four patients with confirmed clinical diagnosis of scoliosis were scanned using a specially developed 3D laser profilometer. The measuring principle of the system is based on laser triangulation with one-laser-plane illumination. The measurement took approximately 10 seconds at 700 mm of the longitudinal translation along the back. The single point measurement accuracy was 0.1 mm. Computer analysis of the measured surface returned two 3D curves. The first curve was determined by manual marking (manual curve), and the second was determined by detecting surface curvature extremes (automatic curve). The manual and automatic curve comparison was given as the root mean square deviation (RMSD) for each patient. The intra-operator study involved assessing 20 successive measurements of the same person, and the inter-operator study involved assessing measurements from 8 operators. The results obtained for the 24 patients showed that the typical RMSD between the manual and automatic curve was 5.0 mm in the frontal plane and 1.0 mm in the sagittal plane, which is a good result compared with palpatory accuracy (9.8 mm). The intra-operator repeatability of the presented method in the frontal and sagittal planes was 0.45 mm and 0.06 mm, respectively. The inter-operator repeatability assessment shows that that the presented method is invariant to the operator of the computer program with the presented method. The main novelty of the presented paper is the development of a new, non-contact method that provides a quick, precise and non-invasive way to determine the spatial spine curve for patients with developed scoliosis and the validation of the presented method using the palpation of the spinous processes, where no harmful ionizing radiation is present.

7 July 2020 in Lasers in Surgery and Medicine
Verified
Journal Article
Open access
PDF file
Matija JezersekMatija Jezersek
Matija Jezersek
NLNejc Lukač
Nejc Lukač
MLMatjaž Lukač
Matjaž Lukač
Background and Objectives: To compare temporal rates of debris removal from an artificial root canal for three laser‐assisted irrigation modalities single‐pulse super short pulse (SSP), and two dual‐pulse X‐SWEEPS and AutoSWEEPS, and for two fiber‐tip (FT) geometries flat and radial, and to evaluate the dependence of the debris flushing rate on the delay between the SWEEPS laser pulse pair.Study Design/Materials and Methods: Laser‐assisted irrigation was performed with a pulsed Er:YAG laser operating in single‐pulse SSP and dual‐pulse SWEEPS laser modalities. The laser energy was delivered to the water‐filled model access cavity through a FT with either a flat or radial ending. The X‐SWEEPS modality delivered pairs of laser pulses separated by a fixed adjustable delay, while with the AutoSWEEPS modality the delay was automatically and repeatedly swept between 200 and 600 microseconds. The debris removal rate was determined with the use of a digital camera by measuring the rate at which a simulated debris was being flushed out of the artificial root canal.Results: The simulated debris removal rate of the AutoSWEEPS modality is almost three times higher compared with that of the SSP modality. Further, the flat FT outperforms the radial FT by a factor of more than five in the case of SSP, and by more than 10 with AutoSWEEPS. The X‐SWEEPS flushing rate exhibits strong dependence on the delay between the SWEEPS pulse pair, with the highest removal rate measured to be more than seven times higher in comparison with SSP.Conclusion: Dual‐pulse laser irrigation modalities (AutoSWEEPS and X‐SWEEPS) exhibit significantly higher simulated debris removal rates in comparison with the standard single‐pulse SSP laser‐assisted irrigation. As opposed to the previously reported dependence of pressure generation on FT geometry, the flat FT's simulated debris removal rate significantly outperforms the radial FT. © 2020 The Authors. Lasers in Surgery and Medicine published by Wiley Periodicals LLC

20 November 2020 in Sensors
Verified
Journal Article
Open access
PDF file
ABAlex Božič
Alex Božič
MKMatjaž Kos
Matjaž Kos
Matija JezersekMatija Jezersek
Matija Jezersek
The increase in complex workpieces with changing geometries demands advanced control algorithms in order to achieve stable welding regimes. Usually, many experiments are required to identify and confirm the correct welding parameters. We present a method for controlling laser power in a remote laser welding system with a convolutional neural network (CNN) via a PID controller, based on optical triangulation feedback. AISI 304 metal sheets with a cumulative thickness of 1.5 mm were used. A total accuracy of 94% was achieved for CNN models on the test datasets. The rise time of the controller to achieve full penetration was less than 1.0 s from the start of welding. The Gradient-weighted Class Activation Mapping (Grad-CAM) method was used to further understand the decision making of the model. It was determined that the CNN focuses mainly on the area of the interaction zone and can act accordingly if this interaction zone changes in size. Based on additional testing, we proposed improvements to increase overall controller performance and response time by implementing a feed-forward approach at the beginning of welding.