This article presents computational fluid dynamics (CFD) modeling of the flow processes at a certain specimen of an external gear pump. The purpose of the developed two-dimensional (2D) CFD model is to carry out a numerical study to obtain the main characteristics of the pump flow rate, especially the flow rate as a function of the pressure and the flow rate as a function of the time. A numerical study was carried out at forty-two different operating modes that were expressed as a variation of two parameters: rotational frequency (950–1450 min⁻¹) and pressure (5–150 bar). The validation of the numerical results was carried out through an experimental study. For this purpose, a laboratory experimental setup equipped with a modern data acquisition (DAQ) system was designed and implemented. It allows the gear pump to be tested at the same operating modes as the numerical study. A validation analysis was performed by comparing the numerical and experimental results using the average relative error index (FIT). A detailed description of the 2D CFD model development (CAD model, mesh, general settings, boundary conditions, etc.) is provided. Based on the 2D CFD model, an original methodology was proposed to take into account the influence of the discharge channels on the displacement volume of the pump by adjusting the face width of the gears. Despite the limitations of the simple 2D CFD model, which are discussed in this article, a very good match between numerical and experimental results is analyzed by calculating the FIT level, which is in the range of 93–97%.

A system for the rapid prototyping of real-time control algorithms for open-circuit variable displacement axial-piston pumps is presented. In order to establish real-time control, and communication and synchronization with the programmable logic controller of an axial piston pump, the custom CAN communication protocol is developed. This protocol is realized as a Simulink^® S-function, which is a part of main Simulink^® model. This model works in real-time and allows for the implementation of rapid prototyping of various control strategies including advanced algorithms such as H∞ control. The aim of the algorithm is to achieve control system performance in the presence of various load disturbances with an admissible control signal rate and amplitude. In contrast to conventional systems, the developed solution suggests using an embedded approach for the prototyping of various algorithms. The obtained results show the advantages of the designed H∞ controller that ensure the robustness of a closed-loop system in the presence of significant load disturbances. These type of systems with displacement volume regulation are important for industrial hydraulic drive systems with relatively high power.

The article presents a developed embedded system for control of electrohydraulic power steering based on multivariable uncertain plant model and advanced control techniques. The plant model is obtained by identification procedure via “black box” system identification and takes into account the deviations of the parameters that characterize the way that the control signal acts on the state of the model. Three types of controller are designed: Linear-Quadratic Gaussian (LQG) controller, H _∞ controller and μ-controller. The main result is a performed comparative analysis of time and frequency domain properties of control systems. The results show the better performance of systems based on µ-controllers. Also the robust stability and robust performance are investigated. All three systems achieved robust stability which guarantees their workability, but only the system with µ-controller has robust performance against prescribed uncertainties. The control algorithms are implemented in specialized 32-bit microcontroller. A number of real world experiments have been executed, which confirm the quality of the electrohydraulic power steering control system.

The article presents an advanced two-dimensional (2D) computational fluid dynamics (CFD) model of an external gear pump which considers relief grooves. Relief grooves are limiting design features for the flow process of this type of pump, and their influence in existing studies is considered by a three-dimensional (3D) model only. The structural modification proposed by the authors is beyond the possibilities of real implementation, but it gives the possibility to precisely model the pump’s design features. In contrast to the existing studies (using 3D CFD), the proposed advanced 2D model requires significantly fewer computing resources. Numerical experiments were carried out using the 2D model at different pump operating modes depending on the rotation frequency (950–1450 min⁻¹) and pressure load (5–150 bar). The numerical results were validated by a real-world experiment for the same pump operating modes using an existing laboratory experimental setup. An analysis of the CFD model and real experiment results was carried out by determining a quantitative index of match (FIT), which varies in the range of 97.93–99.82%. This proves the performance of the proposed CFD model, which can be further used as a part of more complex hydraulic systems models.

The paper compares the performance of two embedded controllers applied in electrohydraulic steering systems – model predictive controller (MPC) and linear-quadratic Gaussian (LQG) controller with Kalman filtering for state estimation. Both controllers are designed on the basis of single input multiple output “black box” model obtained via identification approach. The controllers are implemented into industrial logic controller for mobile applications and their workability is experimentally checked with a laboratory model of a steering system for non-road mobile machinery. The results corresponding to investigation of performance of the closed-loop system are presented.

This article is devoted to a comparison of two advanced control techniques applied to the same plant. The plant is a certain type of axial-piston pump. A linear-quadratic (LQR) controller and an H-infinity (H_∞) controller were synthesized to regulate the displacement volume of the pump. The classical solution to such a problem is to use a hydro-mechanical controller (by pressure, flow rate, or power) but, in the available sources, there are solutions that implement proportional-integral-derivative (PID), LQR, model predictive control (MPC), etc. Unlike a classical solution, in our case, the hydro-mechanical controller is replaced by an electro-hydraulic proportional valve, which receives a reference signal from an industrial microcontroller. It is used as the actuator of the pump swash plate. The pump swash plate swivel angle determines the displacement volume, respectively, and the flow rate of the pump. The microcontroller is capable of embedding various control algorithms with different structures and complexities. The developed LQR and H_∞ controllers are compared in the simulation and real experiment conditions. For this purpose, the authors have developed a laboratory experimental test bench, enabling a real-time function of the control system via USB/CAN communication. Both controllers are compared under different pump loading modes. Also, this paper contributes an uncertain model of an axial-piston pump with proportional valve control that is obtained from experimental data. Based on this model, the robust stability of the closed-loop system is investigated by comparing the structured singular value (μ). The investigations show that both control systems achieved robust stability. Moreover, they can tolerate up to four times larger uncertainties than modeled ones. The system with the H_∞ controller attenuates approximately at least 30 times the disturbances with frequency up to 1 rad/s while the system with the LQR controller attenuates at least 10 times the same disturbances.