Arturo Juárez Hernández

Prof. Dr. Arturo Juárez Hernández

Universidad Autónoma de Nuevo León, San Nicolás de los Garza, Nuevo León, Mexico
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 October 2023 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
JRJuly Taborda Rios
July Taborda Rios
Patricia Zambrano-RobledoPatricia Zambrano-Robledo
Patricia Zambrano-Robledo
JTJuan Daniel Trejos Taborda
Juan Daniel Trejos Taborda
JEJohan Andrés Gómez Espinoza
Johan Andrés Gómez Espinoza
CICatalina Jaramillo Isaza
Catalina Jaramillo Isaza
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández

22 March 2023 in Wear
Verified
Journal Article
Closed access
CCCarlos Cuao-Moreu
Carlos Cuao-Moreu
ICI. Campos-Silva
I. Campos-Silva
ADA.M. Delgado-Brito
A.M. Delgado-Brito
EGE.O. Garcia-Sanchez
E.O. Garcia-Sanchez
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández
Marco A. L. Hernandez-RodriguezMarco A. L. Hernandez-Rodriguez
Marco A. L. Hernandez-Rodriguez

27 September 2021 in Lubricants
Verified
Journal Article
Open access
PDF file
Denis Avila SalgadoDenis Avila Salgado
Denis Avila Salgado
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández
José Cabral MiramontesJosé Cabral Miramontes
José Cabral Miramontes
JMJosé Luis Camacho Martínez
José Luis Camacho Martínez
This work examines the effect of nickel (Ni) and cobalt (Co) concentrations on wear resistance behavior of Cu-xNi-yCo-Cr-Si (x = 8−9 wt%, y = 1−2 wt%) and the zirconium (Zr) addition, in order to obtain an alloy with similar or better properties than the C17510 alloy. In this study, hardness and wear resistance mechanism behavior were associated with the microstructure evolution of these alloys with different aging strengthening conditions. Different heat treatments (HT) were applied to three alloys Cu-8Ni-2Co-1.6Cr-2Si wt% (L1), Cu-8.5Ni-1.5Co-1.6Cr-2Si wt% (L2) and Cu-9Ni-1Co-1.6Cr-2Si-0.18Fe-0.3Zr wt% (L3), the properties obtained were compared with C17510 alloy. Specimens were characterized by different metallographic techniques; the microstructural characterization was made with scanning electron microscopy (SEM) and revealed regions of dendritic morphologies. The solidification sequence is primary Cu dendrites and some phases in the interdendritic regions. The solution heat treatment decreased (ST) the Hardness Rockwell B (HRB) and wear rate resistance, and there was an increase with the first aging heat treatment (HT1) for each alloy. The most outstanding combination of properties was found for Cu-8.5Ni-1.5Co-1.6Cr-2Si wt% alloy (L2C3) with 100 ± 1 HRB and specific wear rate resistance of 1.2 × 10−4 mm3/Nm, after the first aging heat treatment.

26 August 2022 in Entropy
Verified
Journal Article
Open access
PDF file
Denis Avila SalgadoDenis Avila Salgado
Denis Avila Salgado
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández
MLMaria Del Refugio Lara-Banda
Maria Del Refugio Lara-Banda
ABArnoldo Bedolla-Jacuinde
Arnoldo Bedolla-Jacuinde
FGFrancisco V Guerra
Francisco V Guerra
In this research, a set of CuNiCrSiCoTi (H-0Nb), CuNiCrSiCoTiNb0.5 (H-0.5Nb) and CuNiCrSiCoTiNb1 (H-1Nb) high-entropy alloys (HEAs) were melted in a vacuum induction furnace. The effects of Nb additions on the microstructure, hardness, and wear behavior of these HEAs (compared with a CuBe commercial alloy) in the as-cast (AC) condition, and after solution (SHT) and aging (AT) heat treatments, were investigated using X-ray diffraction, optical microscopy, and electron microscopy. A ball-on-disc configuration tribometer was used to study wear behavior. XRD and SEM results showed that an increase in Nb additions and modification by heat treatment (HT) favored the formation of BCC and FCC crystal structures (CS), dendritic regions, and the precipitation of phases that promoted microstructure refinement during solidification. Increases in hardness of HEA systems were recorded after heat treatment and Nb additions. Maximum hardness values were recorded for the H-1Nb alloy with measured increases from 107.53 HRB (AC) to 112.98 HRB, and from 1104 HV to 1230 HV (aged for 60 min). However, the increase in hardness caused by Nb additions did not contribute to wear resistance response. This can be attributed to a high distribution of precipitated phases rich in high-hardness NiSiTi and CrSi. Finally, the H-0Nb alloy exhibited the best wear resistance behavior in the aged condition of 30 min, with a material loss of 0.92 mm3.

6 May 2020 in Metals
Verified
Journal Article
Open access
PDF file
Denis Avila SalgadoDenis Avila Salgado
Denis Avila Salgado
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández
FMFermín Medina-Ortíz
Fermín Medina-Ortíz
MLMaria Del Refugio Lara-Banda
Maria Del Refugio Lara-Banda
Marco A. L. Hernandez-RodriguezMarco A. L. Hernandez-Rodriguez
Marco A. L. Hernandez-Rodriguez
During the high pressure die casting process (HPDC), it is necessary to develop new designs and alloys for the copper plungers. In this research, two alloys Cu-9Ni-1Co-1.6Cr-2Si-1.3Fe-0.25B wt.% (A1) and Cu-9Ni-1Co-1.6Cr-2Si-0.1Fe-0.2Nb wt.% (A2) under different heat treatments (HT) were studied. Optical microscopy technique was applied to reveal the regions of dendritic morphology, also lower Secondary Dendrite Arm Spacing (SDAS); and different grain orientations. The results reveal that the solidification sequence is primary Cu dendrites and secondary intermetallics; heat treatments increase the redistribution of alloying elements in the interdendritic regions. During the heat treatments, some precipitates were found in the grain boundary after aging heat treatments for both alloys, which were determined by X-ray diffraction. Hardness test HRB presented a decrease with the solution heat treatment and an increase with the aging heat treatments proposed for both alloys. Finally, the wear resistances for both alloys were compared with a commercial alloy C17530, with decreased A1 with B additions having the best result in the as-cast condition 4.07 × 10−4 mm3/Nm, while for A2 with Nb additions wear resistance increased, with the best result in the one with aging heat treatment 1.69 × 10−4 mm3/Nm while for the C17530 alloy this was 2.74 × 10−4 mm3/Nm.

5 April 2025 in Lubricants
Verified
Journal Article
Open access
PDF file
Denis Avila SalgadoDenis Avila Salgado
Denis Avila Salgado
Arturo Juárez HernándezArturo Juárez Hernández
Arturo Juárez Hernández
NINelson Javier Izaguirre-Bonilla
Nelson Javier Izaguirre-Bonilla
Jonathan Muñoz TaboraJonathan Muñoz Tabora
Jonathan Muñoz Tabora
JMJosé Luis Camacho Martínez
José Luis Camacho Martínez
Medium-entropy alloys (MEAs) allow the formation of different phases, generally in a solid-solution state, and compounds that favor obtaining alloys with properties superior to those of conventional alloys. In this study, medium-entropy CuNiSiCrCoTiNbx alloys were fabricated via melting in a vacuum induction furnace. The influence of the Nb addition (X = 0, 0.5 and 1 wt%) alloying elements on the microstructure, hardness, and wear resistance of the CuNiSiCrCoTiNb0 (M1), CuNiSiCrCoTiNb0.5 (M2), and CuNiCoCrSiTiNb1 (M3) alloys were explored using X-ray diffraction (XRD), scanning electron microscopy (SEM), and a ball-on-disc tribometer, respectively. In general, the results indicated that the incorporation of Nb alloying element promoted the evolution of the microstructure, increased the hardness, and improvement of the wear resistance. The XRD and SEM findings demonstrate that higher Nb addition and aging heat treatment (AT) modification mainly favored the formation of dendritic regions and the precipitation of the Co2Nb, Cr3Si, and Ni2Si phases, which promoted the refinement and strengthening of the microstructure. Significant increases in hardness were recorded: 11.95% increased, promoted by the addition of Nb before (E1) and after (E2, E3, and E4) the heat treatments. The maximum hardness values recorded were 92 ± 0.11 (AC) and 103 ± 0.5 HRB (AT-60 min) for the M3 alloy. The increase in hardness caused by Nb addition and aging heat treatments contributed to the dry sliding wear resistance response, decreasing material loss by 20%. This was related to the high concentration of precipitated phases rich in CoNb, CrSi, and NiSi with high hardness. Finally, the M3 alloy aged for 60 min exhibited the best specific wear rate behavior, with a material loss of 1.29 mm3. The commercial Cu-Be C17510 alloy experienced a maximum hardness of 83.47 Hardness Rockwell B, HRB, and a high wear rate of 3.34 mm3.