Among the advanced oxidation processes (AOPs), the Fenton reaction has attracted much attention in recent years for the treatment of water and wastewater. This review provides insight into a particular variant of the process, where soluble Fe(II) salts are replaced by zero-valent iron (ZVI), and hydrogen peroxide (H₂O₂) is replaced by persulfate (S₂O₈²⁻). Heterogeneous Fenton with ZVI has the advantage of minimizing a major problem found with homogeneous Fenton. Indeed, the precipitation of Fe(III) at pH > 4 interferes with the recycling of Fe species and inhibits oxidation in homogeneous Fenton; in contrast, suspended ZVI as iron source is less sensitive to the increase of pH. Moreover, persulfate favors the production of sulfate radicals (SO₄^•−) that are more selective towards pollutant degradation, compared to the hydroxyl radicals (^•OH) produced in classic, H₂O₂-based Fenton. Higher selectivity means that degradation of SO₄^•−-reactive contaminants is less affected by interfering agents typically found in wastewater; however, the ability of SO₄^•− to oxidize H₂O/OH⁻ to ^•OH makes it difficult to obtain conditions where SO₄^•− is the only reactive species. Research results have shown that ZVI-Fenton with persulfate works best at acidic pH, but it is often possible to get reasonable degradation at pH values that are not too far from neutrality. Moreover, inorganic ions that are very common in water and wastewater (Cl⁻, HCO₃⁻, CO₃²⁻, NO₃⁻, NO₂⁻) can sometimes inhibit degradation by scavenging SO₄^•− and/or ^•OH, but in other cases they even enhance the process. Therefore, ZVI-Fenton with persulfate might perform unexpectedly well in some saline waters, although the possible formation of harmful by-products upon oxidation of the anions cannot be ruled out.

Marine sediments and sessile biota (i.e. oysters) are nowadays recognised to be affected by microplastic (MP) pollution. NOAA proposes two distinct MP extraction protocols for sandy and bed sediments, which, however, were already demonstrated to suffer from many limitations. Conversely, to what concern oysters, works already published are usually time consuming, requiring a KOH 24–48 h oxidation step. The aim of this study is to show how iterative adaptation of the NOAA protocol allows to extract MPs, included PET, from marine sediments, regardless their characteristics. The method tested on PE-LD/PET/PA/PE-HD is based on density separation and oxidation treatments which were both carefully tuned, obtaining final recoveries higher than 85% for all the micropolymers (100% for PE and PA). Furthermore, a new protocol for the extraction of MPs from oysters was assessed, highlighting its efficacy (recoveries higher than 84% for all the plastics) and time-saving peculiarity. Finally, both protocols were successfully applied in the MPs extraction from real samples from Atlantic Ocean.•The extraction of PE-LD/PET/PA/PE-HD was optimised in sediments (regardless their characteristics) and oysters.•For sediments, density separation and oxidation procedures were carefully optimised.•For oysters, oxidation times were reduced from 24 to 48 h to 1 h.

Over the past decade, biochar (BC) has received significant attention in many environmental applications, including water purification, since it is available as a low-cost by-product of the energetic valorisation of biomass. Biochar has many intrinsic characteristics, including its porous structure, which is similar to that of activated carbon (AC), which is the most widely used sorbent in water treatment. The physicochemical and performance characteristics of BCs are usually non-homogenously investigated, with several studies only evaluating limited parameters, depending on the individual perspective of the author. Within this review, we have taken an innovative approach to critically survey the methodologies that are generally used to characterize BCs and ACs to propose a comprehensive and ready-to-use database of protocols. Discussion about the parameters of chars that are usually correlated with adsorption performance in water purification is proposed, and we will also consider the physicochemical properties of pollutants (i.e., K_ow). Uniquely, an adsorption efficiency index BC/AC is presented and discussed, which is accompanied by an economic perspective. According to our survey, non-homogeneous characterization approaches limit the understanding of the correlations between the pollutants to be removed and the physicochemical features of BCs. Moreover, the investigations of BC as an adsorption medium necessitate dedicated parallel studies to compare BC characteristics and performances with those of ACs.