For the adsorption of copper (II) and zinc (II) ions from polluted water, an efficient inexpensive nanoadsorbent; nickel ferrite modified montmorillonite nanocomposite was synthesized by co-precipitation of the mechano-chemically modified montmorillonite with the salts of nickel and iron. The natural MMT, modified MMT, and the synthesized nickel ferrite modified montmorillonite (NiFe2O4-Mod MMT) nanoadsorbent were characterized by several techniques including Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, energy-dispersive X-ray, surface area analysis, saturation magnetization, and surface zeta potential. Batch studies were carried out on the effect of various parameters including contact time, nanocomposite dosage, solution pH, metal ion initial concentration, and temperature on the adsorption process to optimize its conditions. The equilibrium state was reached after 60 min and 90 min of reaction for Cu (II) and Zn (II) ions, respectively. The optimum conditions were 0.1 g adsorbent dose, pH 5, 13 mg/L initial metal ion concentration and 298 K temperature for copper (II) adsorption and 0.1 g adsorbent dose, pH 6, 6 mg/L initial metal ion concentration, and 298 K temperature for zinc (II) adsorption. Among the designed kinetic and equilibrium models, the pseudo-second-order kinetic model and Langmuir adsorption isotherm model have controlled the adsorption process for both metal ions. Furthermore, the adsorption mechanism and the reproducibility of the nanoadsorbent were investigated. The maximum adsorption efficiency was 99.23% and 91.67% of copper (II) and zinc (II) ions, respectively.
This paper studies the removal of ethyl naphthalene as one of the polyaromatic hydrocarbon pollutants (PAHs) from the produced water. Magnetic super hydrophobic monolithic core-shell polystyrene (MSHMCSh@PS) was prepared using a simple and low-cost (facile in situ bulk radical polymerization) method, in the presence of 2-azobisisobutyronitrile as an initiator for ethyl naphthalene adsorption. The characterization of the MSHMCSh@PS was performed using FT-IR, TGA, SEM, TEM, and VSM. The possibility of PAHs adsorption from produced water was performed using the continuous adsorption study in a fixed-bed column. The effects of flow rate, concentration, and bed height were investigated. The results showed that the relationship between adsorption capacity with both inlet concentration and bed depth is a direct one, while the relationship between adsorption capacity and flow rate is an inverse relationship. The best column parameters were found at 2.5 ml/min flowing rate, 9 cm bed height, and 50 mg/L concentration. The experimental column results and the relationship between operating boundaries were analyzed according to Yoon-Nelson and Thomas models. The results indicated that the breakthrough curve follows the Yoon-Nelson model. The practical application results showed that the PAHs were adsorbed from the produced water using the prepared absorbent MSHMCSh@PS, which was distinguished by its superior ability.
The problem of wax precipitation and deposition in crude oils at low temperatures causes severe problems in the petroleum industry. Among the various developed approaches to solve this issue is the injection of polymer nano-composites into waxy crude oil. Herein, the bagasse of sugarcane waste as a bioresource was used for silica nano-particles (Nano-SiO2) extraction. Also, a new copolymer of styrene-co-vinyl acetate was prepared then, a novel nano-composite; Nano-SiO2/styrene-co-vinyl acetate composed of the produced bioresoursed Nano-SiO2 and styrene-co-vinyl acetate was prepared. Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and gel permeation chromatography analytical techniques were used to characterize the produced materials. Additionally, the synthesized Nano-SiO2/styrene-co-vinyl acetate was applied as a cheap nano-pour point depressant and paraffin inhibitor for the waxy crude oil and its performance was compared with the pristine styrene-co-vinyl acetate copolymer. Various concentrations (100 ppm-800 ppm) of the synthesized additives were injected into the collected crude oil samples at 60 ºC. The results indicated that the dosages of the injected pour point depressants have a significant impact on their performance. Optimum dosages of 400 ppm and 600 ppm of Nano-SiO2/styrene-co-vinyl acetate and styrene-co-vinyl acetate respectively were found to be efficient in depressing the pour point temperature and inhibiting the paraffins aggregation at low temperatures.