Hsiao-Hsing Chou

Prof. Hsiao-Hsing Chou

orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
3 November 2022 in IEEE Transactions on Circuits and Systems II: Express Briefs
Verified
Journal Article
Closed access
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
This paper presents a new LED control scheme to maintain a constant LED power. In LED control schemes, the conventional approach is to maintain a constant LED current. However, this traditional approach will bring high power at high input voltage and then generate high heat. The higher heat will shorten the life time of the product and reduce the reliability. The proposed scheme can solve this problem. The LED driver with the proposed scheme has been successfully fabricated by Macronix and the feasibility of the method has been verified. From the experimental results, the higher the input voltage, the lower the LED current. This constant power method can effectively avoid overheating at high input voltage. The control scheme, the theoretical analysis and the circuit implementation are presented in this paper.

3 September 2021 in Electronics
Verified
Journal Article
Open access
PDF file
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
HCHsin Liang Chen
Hsin Liang Chen
YFYang-Hsin Fan
Yang-Hsin Fan
San Fu WangSan Fu Wang
San Fu Wang
This study presents a new virtual inductor current circuit to reduce circuit complexity, which is not necessary to sense inductance current directly. The buck converter was designed to produce an output voltage of 1.0–2.5 V for a 3.0–3.6 V input voltage. The load current range was from 100 mA to 500 mA. It was simulated and verified by SIMPLIS and MathCAD. The simulation results of this buck converter show that the voltage error is within 1%, and the recovery time is smaller than 2 ms for step-up and step-down load transients. Additionally, it achieves less than 26 mV overshoot at full-load step transient response. The circuit topology would be able to fabricate using TSMC 0.35 mm 2P4M CMOS technology. The control mechanism, implementation, and design procedure are presented in this paper.

15 April 2022 in Electronics
Verified
Journal Article
Open access
PDF file
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
WLWen-Hao Luo
Wen-Hao Luo
HCHsin Liang Chen
Hsin Liang Chen
San Fu WangSan Fu Wang
San Fu Wang
This paper presents a novel buck converter with dual-loop control technology, which does not need to detect the inductor current directly. The structure of the control loops is easy to implement, one loop controls the output voltage, and the other controls the switching frequency. With the dual loops control mechanism, the output voltage and switching frequency can be accurately controlled only by measuring the output and input voltage, without sensing the inductor current. The buck converter can generate an output voltage of 1.0–2.5 V when the input voltage and load current are 3.0–3.6 V and 100–500 mA, respectively. The design was verified by SIMPLIS. The simulation results show that the switching frequency variation is less than 1% at the output voltage of 1.0–2.5 V. The recovery time is less than 1.5 μs during the load change. The circuit can be fabricated by using the TSMC 0.35μm 2P4M CMOS processes. The control scheme, theoretical analysis and circuit implementation are presented in this paper.

17 September 2021 in Energies
Verified
Journal Article
Open access
PDF file
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
HCHsin Liang Chen
Hsin Liang Chen
This paper presents a buck converter with a novel constant frequency controlled technique, which employs the proposed frequency detector and adaptive on-time control (AOT) logic to lock the switching frequency. The control scheme, design concept, and circuit realization are presented. In contrast to a complex phase lock loop (PLL), the proposed scheme is easy to implement. With this novel technique, a buck converter is designed to produce an output voltage of 1.0–2.5 V at the input voltage of 3.0–3.6 V and the maximum load current of 500 mA. The proposed scheme was verified using SIMPLIS and MathCAD. The simulation results show that the switching frequency variation is less than 1% at an output voltage of 1.0–2.5 V. Furthermore, the recovery time is less than 2 μs for a step-up and step-down load transient. The circuit will be fabricated using UMC 0.18 μm 1P6M CMOS processes. The control scheme, design concept and circuit realization are presented in this paper.

3 February 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
JCJian-Yu Chen
Jian-Yu Chen
TTTsung-Hu Tseng
Tsung-Hu Tseng
JYJun-Yi Yang
Jun-Yi Yang
XYXuan Yang
Xuan Yang
San Fu WangSan Fu Wang
San Fu Wang
In this paper, a new control scheme for buck converters was proposed. The buck converter utilizes the dual control loop to improve transient response and has the constant switching frequency. The control scheme is mainly as follows: (a) The switch-ON time is regulated by the constant frequency mechanism. (b) The switch-OFF time is regulated by the output voltage. The spec/features of the proposed converter are listed as: (1) The buck converter has an output of 1.0–2.5 V for the input of 3.0–3.6 V. The load current ranges from 100 mA to 500 mA. (2) The actual current sensor is not required. (3) The simulation results show that the recovery time is less than 1.6 μs during load changes. (4) The variation in switching frequency is smaller than 1.05% over the output range of 1.0–2.5 V. (5) This circuit can be fabricated in future by UMC 0.18 μm 1P6M CMOS processes. This paper depicts the control scheme, theoretical analysis, and implementation.

5 May 2022 in Electronics
Verified
Journal Article
Open access
PDF file
Hsiao-Hsing ChouHsiao-Hsing Chou
Hsiao-Hsing Chou
WLWen-Hao Luo
Wen-Hao Luo
San Fu WangSan Fu Wang
San Fu Wang
This paper proposes a novel control scheme for the buck converter without an inductor current sensor. The architecture of the proposed buck converter is simple and suitable for integration and mass production. It employs an output-voltage-measurement method to determine the switch ON time; therefore, the current sensor is not required. The design specification targets the application with a standard battery power source to generate the low voltages for low-power MCU or ASIC. The load current range aims for several hundred milliamps. The proposed control scheme is analyzed and simulated by SIMPLIS. The control scheme, theoretical analysis, circuit realization, contributions, advantages, and simulation results are presented in this paper. Furthermore, the circuit can be fabricated by a 0.35 μm CMOS process.