The high-rate discharging performance of a lithium titanate battery is one of its main properties. In conditions that require ultra-high-rate discharging, a lithium titanate battery can be discharged continuously at a current of 50 C (50 times of its maximum capacity) or higher. In this paper, we take cylindrical steel shell lithium titanate cells as the research object and perform aging cycles at 66 C on these cells. The ultra-high-rate discharging cycles cause a rapid high-power capacity fading while the available capacity at normal current rate is not affected. The capacity at 66 C decreases to 80% of initial value in 10 cycles. This paper also analyzes the aging process of a lithium titanate battery at high-rate discharging with incremental capacity (IC) analysis, and presents the aging behavior of lithium titanate battery qualitatively, which is inconsistent with existing research. We attribute the aging mechanism of ultra-high-rate discharging cycles to the decrease of ionic mobility and increase of polarization resistance. Mechanical damage is observed in the CT scan of an aged cell, which we presume to be the result of rapid strain of cathode material.
The high-rate discharging performance of lithium titanate batteries is a crucial aspect of their functionality. Under high-power demands, the discharge rate, which is defined as the ratio of discharge current to the maximum capacity, can exceed 50 C or higher. This study investigates the evolution of incremental capacity (IC) curves and frequency response characteristic of 2 Ah lithium titanate batteries subjected to aging cycles at 50 C. The results provide a new indicator to assess the fading of the state of health (SOH) of lithium titanate batteries during ultra-high-rate discharge cycles.
The charging time of Li-ion batteries connected in series (LBCSs) power supply is the main concern in an electromagnetic propulsion system. However, the capacity loss of a Li-ion battery is inevitable due to the repetitive operation of LBCSs power supply, which leads to the decrease in the average current. Thus, the voltages of symmetrically distributed pulse capacitors of LBCSs power supply will not reach the setting value in the specified time. This paper proposes a novel closed-loop control method to solve the problem. By collecting the pulse capacitor voltage and the circuit current, the time sequences of Li-ion batteries are recalculated in real time in a closed-loop to increase the average current. The time-domain model of the circuit topology of the LBCSs power supply and an innovative closed-loop control method based on the time sequences recalculation algorithm are described first. Then, the circuit model is built in PSIM for simulation analyses. Finally, a series of experiments are conducted to confirm the effectiveness of the method on the megawatt LBCSs power supply platform. Both the simulation and experimental results validate that the proposed method not only shortens the charging time, but also increases the average current. In practical experiments, the charging time is shortened by 4.5% and the average current is increased by 4.8% using the proposed method at the capacity loss of 50 V.
A lithium titanate oxide (LTO) anode based battery has high power density, and it is widely applied in transportation and energy storage systems. However, the thermal performance of LTO anode based battery module is seldom studied. In this work, a heat generation theoretical model of the battery is explored. The thermal performance of LTO anode based battery modules under high discharge rates is studied by both experiment and simulation. It is found that the temperature rise of the battery can be estimated accurately with the calculation of the equivalent internal resistance under different discharge rates. In addition, under the same depth of discharge, both the temperature rise and the temperature difference in the battery module increase with the discharge rates.
20 January 2023 in IEEE Transactions on Plasma Science
Pulsed alternator is widely concerned in the field of pulse power supply, and the heat generation of the field coil is an important reason for the temperature rise of the rotor, which is unfavorable to the thermal management of the pulsed alternator. Therefore, a parallel excitation and serial recovery magnetic energy recovery topology for the separate excitation pulsed alternator is proposed in this article. In contrast with the conventional (no recovery) topology, there are two changes in this topology. One is that the diode is replaced by a thyristor in freewheeling circuit, which can realize the switching of the field current from the freewheeling state to the recovery state. The other is that serial recovery topology is used, which can realize the rapid recovery of magnetic energy. First, the analytical expressions of the field current and the pulse capacitor voltage are derived under the three states of parallel excitation, freewheeling, and serial recovery. Second, four performance parameters for evaluating topology are derived based on the obtained analytical expressions. Third, the influence of the number of serial modules $n$ on the four performance parameters is analyzed. Finally, the maximum value of $n$ is solved, and the simulation models under different $n$ values are built. The simulation results verify the correctness of the analytical model and the benefits and losses of the magnetic energy recovery topology are discussed.
3 June 2019 in IEEE Transactions on Plasma Science
As the development of pulse power technology, the pulse power supply modules (PPSMs) are widely used in areas of scientific research, medical treatment, industry, military, and geological prospecting. In these areas, more and more energy is needed and the number of PPSM is increasing rapidly, and the accurate pulse discharging waveforms are required in some applications. How to control so many PPSM to discharge in a precise time sequence effectively becomes one of the key points in the pulse power technology. According to the requirements of a pulse discharging velocity source, a time sequence discharging control system is designed, which can control 30 PPSMs to discharge in a precise time sequence. In this control system, the digital signal processor (DSP) is used as the main control chip. The high-speed photoelectric converters and optical fibers are used as the trigger signals transmission system. The time sequence can be set by using the upper computer software, and the accuracy of the trigger pulses can reach to the microsecond level. This control system is used in the actual experiments of the speed source, and the results proved that the control system is effective.