Acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) are considered a well-known class of engineering thermoplastics due to their efficient use in automotive, 3D printing, and electronics. However, improvement in toughness, processability, and thermal stability is achieved by mixing together ABS and PC. The present study focuses on the understanding of surface mechanical characterization of acrylonitrile butadiene styrene (ABS) and polycarbonate (PC) blends using nano-indentation. Polymer blends sheets with three different proportions of ABS/PC (75:25, 50:50, and 25:75) were fabricated via melt-processing and thermal press. Fourier transform infrared (FTIR) spectroscopy was performed to analyze the intermolecular interactions between the blends’ components. To understand the surface mechanical properties of ABS and PC blends, a sufficient number of nano-indentation tests were performed at a constant loading rate to a maximum load of 100 mN. Creeping effects were observed at the end of loading and start of unloading section. Elastic modulus, indentation hardness, and creep values were measured as a function of penetration displacement in the quasi-continuous stiffness mode (QCSM) indentation. Load-displacement curves indicated an increase in the displacement with the increase in ABS contents while a decreasing trend was observed in the hardness and elastic modulus values as the ABS content was increased. We believe this study would provide an effective pathway for developing new polymer blends with enhanced mechanical performance.

Cryogenic air separation processes are widely used for the large-scale production of nitrogen and oxygen. The most widely used design for this process involves two distillation columns operating at different pressures. This work focuses on the selection of suitable cryogenic air separation process by evaluating seven alternative designs of the two-column air separation process based on detailed exergy analysis. The feed conditions (500 tons/h, and 50% relative humidity of air), product purities (99 mole% for both nitrogen and oxygen), and operational conditions (pressures of both distillation columns) are kept same in all designs. The two cryogenic distillation columns in each configuration are heat-integrated to eliminate the need for external utilities. Steady-state simulation results are used to calculate the exergy efficiency (%) of each equipment as well as its contribution toward the overall exergy destruction rate (kW) of the process. The results show that the compression section is a major source of exergy destruction, followed by the low-pressure column, and the multi-stream heat exchanger. A Petlyuk-like configuration, labeled as C1, provides the lowest exergy destruction rate.

Dyes are the most carcinogenic organic compounds that are discarded by most of the textile industries without any prior treatment, which is harmful for the environment. This study aims to develop a bentonite-clay/carbon-nanotube (CNT)-based adsorbent to treat textile wastewater for water sustainability. The preliminary and post-characterization of adsorbent involves scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and Brunauer–Emmett–Teller (BET) and energy-dispersive X-ray (EDX) analysis to determine the changes in surface morphology, functional group, and surface area of the adsorbent. Linear and nonlinear isotherms and kinetic studies were performed to explore the sorption mechanism. The results show that the nonlinear form of the Langmuir isotherm best fits adsorption with a qmax of 550 mg/g. The adsorption followed the nonlinear pseudo-first-order kinetics, favoring chemisorption with R² ≈ 1 and X₂ = 0.22. Maximum dye removal (89.9%) was achieved under the optimum conditions of pH 3, an adsorbent dose of 100 mg, and a contact time of 120 min, with an initial COD concentration of 1140 mgL⁻¹. This study has demonstrated the successful application of a bentonite-clay/CNT-based adsorbent on textile wastewater treatment.

Doping with heteroatoms is the main method used to enhance energy storage with carbon materials, and polyatomic doping is one of the main challenges. Hydrothermal carbonization of cellulose was performed at 240 °C for 1 h. Ammonium sulfate and thiourea dopants were selected as the sources of inorganic nitrogen and organic nitrogen in the preparation of supercapacitor carbon. The effects of boric acid on the properties of the resulting hydrochar after KOH activation were examined. The results showed that the proportion of functional groups and the specific surface area of the activated hydrochar were reduced by the addition of boric acid, and the formation of micropores was inhibited. The hydrochar obtained from the reaction of cellulose and organic nitrogen compounds had a better pore size distribution and electrochemical properties after activation. The largest specific surface area (952.27 m²/g) was obtained when thiourea was used as the sole dopant. In a three-electrode system, the specific capacitance of the activated hydrochar reached 235.8 F/g at a current density of 1 A/g. After 20,000 charging and discharging cycles at a current density of 10 A/g, the capacitance retention rate was 99.96%. Therefore, this study showed that supercapacitor carbon with good electrochemical properties was obtained by the direct reactions of cellulose with organic nitrogen compounds.

This study aims to investigate the treatment of real textile wastewater using a novel bentonite clay/TiO₂/ZnO-based ozonation catalyst. In this study, synergic electroflocculation/catalytic ozonation, catalytic ozonation, and ozonation processes are applied in a modified hybrid reactor. To the authors’ knowledge, this is the first application of bentonite clay/TiO₂/ZnO as an ozonation catalyst for treating real textile wastewater. The four operational variables—ozone dose (0.2–0.8 mg/min), reaction time (0–120 min), DC voltage supply (5–15 V), and catalyst dose (0.5–2 g/L)—were studied for decolorization and for the removal of chemical oxygen demand (COD). The results showed that the combined process (electroflocculation + clay/TiO₂/ZnO/O₃) had the highest removal efficiencies for COD and color (97.86% and 97.90%, respectively) at optimum parameters of 10 DC volts. an ozone dose of 0.8 mg/min, and a catalyst dose of 2 g/L in textile wastewater. The results further revealed that the initial pH of wastewater plays an essential role in the process’s overall performance. The studied synergic process was efficient for real wastewater treatment under alkaline pH (6–9). Based on empirical work, we established that the synergic process is suitable for effectively treating textile wastewater.