This paper reports research on the frictional behavior of a textured surface against several materials under dry and lubricated conditions, and this is aimed to provide design guidelines on the surface texturing for wide-ranging industrial applications. Experiments were performed on a tribo-tester with the facility of simulating A ball-on-plate model in reciprocating motion under dry, oil-lubricated, and water-lubricated conditions. To study the frictional behavior of textured SiC against various materials, three types of ball-bearing –elements, 52100 steel, silicon nitride (Si₃N₄), and polytetrafluoroethylene (PTFE), were used. Friction and wear performance of an un-textured surface and two types of widely used micro-scale texture surfaces, grooves and circular dimples, were examined and compared. The results demonstrated that the effect of surface textures on friction and wear performance is influenced by texture parameters and the materials of friction pairs. The circular-dimple texture and the groove texture, with certain texture parameters, played a positive role in improving friction and wear performance under specific operating conditions used in this research for SiC–steel and SiC–Si₃N₄ friction pairs; however, there was no friction and wear improvement for the textured SiC–PTFE friction pair. The results of this study offer an understanding and a knowledge base to enhance the performance of bearing elements in complex interacting systems.

Processing texture on contact surfaces can improve the friction performance of mechanical comments. In this research, micro-dimple textures with various parameter were processed on a steel ball’s surface with a picosecond laser. Then, the EHL (elastohydrodynamic lubrication) oil film thickness was measured on an optical ball-on-disc tribometer subjected to pure sliding conditions. The effects of sliding velocity, load, dimple location and dimple depth on the film thickness were analyzed. The results showed that the dimple affected the pressure distribution in the contact area, which in turn changed the distribution of the local film thickness. An increase in the local film thickness occurred between the dimple and outlet of the contact region, while a decrease in the film thickness formed from the dimple to the entrance of the contact area and both sides of the dimple’s edge. Velocity and applied loads affected the film thickness distribution as well. As the sliding velocity increased, the film thickness increasing region enlarged, while the film thickness-decreasing area shrank. The increase in load resulted in a negative effect on the increase in film thickness. This study will provide a reference for point-contact designs with low friction conditions.

The bearing cage played a pivotal role in affecting the lubricant redistribution and lubrication states. In this study, a cage unit is incorporated into an optical ball-on-disc apparatus for the purpose of a quantitative study of cage-induced lubrication phenomena. It is found that the presence of the lubricant layer on the ball surface, shaped by the cage, affects the inlet lubricant supply of contact between the ball and the glass disc. Thereafter, the oil reservoirs surrounding the contact area and the film thickness were measured. The results showed that the lubricant reservoirs and inlet lubricant supplement were significantly improved with the employment of the cages. In addition, the lubrication state transformed from starved to fully flooded, effectively enhancing the lubrication state. Moreover, the lubricant on the steel ball surface moved from the side bands to the central rolling track, indicating that the lubricant redistribution was the main reason for the lubricating enhancement. Notably, the groove modification on the inner surface of the cage pocket facilitated the directional lubricant migration and the migration effect depended on the groove angles. In conclusion, these results offer an in-depth understanding of the bearing lubrication mechanism, thereby inspiring advancements in cage design and lubricant flow regulation.

Seal performance of a novel gas mechanical face seal with semi salix leaf textures was introduced and theoretically investigated with the purpose of enhancing hydrostatic and hydrodynamic opening performance. First, a theoretical model of a laser surface textured gas mechanical face seal with semi salix leaf textures was developed. Second, the impact of operating and texturing parameters on open force, leakage, and friction torque was numerically investigated and has been discussed based on gas lubrication theory. Numerical results demonstrate that the semi salix leaf textured gas face seal has larger hydrostatic and hydrodynamic effects than the semi ellipse textured seal because of the effect of the inlet groove. All semi salix leaf textured surfaces had better open performance than the semi ellipse textured surface, which means that the inlet groove plays an important role in improving open performance and consequently decreasing contact friction during the start-up stage. Texturing parameters also influenced the seal performance of thee semi salix leaf textured gas face seal. When the inclination angle was 50°, the radial proportion of the inlet groove was 0.8, the dimple number was 9, and the open force resulted in the maximum value. This research has demonstrated the positive effects of the applications of a semi salix leaf textured gas mechanical face seal that combines the excellent hydrostatic and hydrodynamic effects of groove texture and the excellent wear resistance of microporous textures.

During petroleum drilling, the reciprocating motion in the seal device leads to piston and sleeve wear, which may cause leakage of the sealing medium. Selecting appropriate materials for the piston and sleeve, along with surface modifications, can effectively prolong the seal service life of the seal. The friction and wear properties of piston and sleeve pairs of different materials in a metal sealing device were simulated by the laboratory “pin-on-block” reciprocating friction test. Pins made of 45# steel, 35CrMo, and 20Cr13 were used to simulate piston bulges, while 35CrMo samples were used to simulate sleeves. Additionally, the influence of DLC (diamond-like carbon) coating and QPQ (Quench–Polish–Quench) nitriding on the wear resistance of the materials was studied. Based on this, the friction and wear properties, along with the wear mechanism of different material pairs, were analyzed. The results show that the friction coefficient curves of the three piston base materials and the 35CrMo sleeve are similar, and the friction coefficient of 45# steel is lower than that of 35CrMo and 20Cr13 at the initial stage. The DLC surface coating exhibited the best anti-wear performance, with the lowest friction coefficient, minimal wear, and the most stable friction coefficient. Surface QPQ nitriding treatment can also improve the wear resistance of the base material. However, due to the oxide formed during nitriding being prone to flaking, the friction coefficient fluctuates significantly at the initial stage of testing, and its anti-wear performance was inferior to that of the DLC coating. This study on material pairing and surface modification provides theoretical support for material selection and surface modification design of pistons and sleeves in oil drilling sealing devices.

The phase behavior of CBABC pentablock terpolymers confined in thin films is investigated using the Dissipative Particle Dynamic method. Phase diagrams are constructed and used to reveal how chain length ($i$-block length), block composition and wall selectivity influence the self-assembly structures. Under neutral walls, four categories of morphologies, i.e., perpendicular lamellae, core–shell types of microstructures, complex networks, and half-domain morphologies, are identified with the change in $i$-block length. Ordered structures are more common at weak polymer–polymer interaction strengths. For polymers of a consistent chain length, when one of the three components has a relatively smaller length, the morphologies transition is sensitive to block composition. With selective walls, parallel lamellae structures are prevalent. Wall selectivity also impacts chain conformations. While a large portion of chains form loop conformations under A-selective walls, more chains adopt bridge conformation when the wall prefers C-blocks. These findings offer insights for designing nanopatterns using symmetric pentablock terpolymers.