Kush Mehta

Dr. Kush Mehta

Associate Professor, Mechanical Engineering, School of Energy Systems, LUT University, Lappeenranta, Finland
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 March 2015 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
Kush MehtaKush Mehta
Kush Mehta
VBVishvesh J. Badheka
Vishvesh J. Badheka

16 December 2014 in Materials and Manufacturing Processes
Verified
Journal Article
Closed access
Kush MehtaKush Mehta
Kush Mehta
VBVishvesh Badheka
Vishvesh Badheka
In the present investigation, dissimilar materials such as electrolytic tough pitch copper, and aluminum 6061-T651 were welded by friction stir welding technology. Effects of tool tilt angle on the mechanical and metallurgical properties were studied experimentally for dissimilar material systems. In the present study, the tool tilt angle was varied from 0° to 4° with an interval of 1°, while the other parameters such as rotational speed, welding speed, tool pin offset, and workpiece material position were kept constant. Macrostructure analysis, tensile test, macro hardness measurement, scanning electron microscopy, and energy dispersive x-ray spectrographic tests were performed to evaluate the weld properties of dissimilar copper–aluminum joints. The results revealed that a defect free dissimilar copper–aluminum friction stir welding was achieved by tilt angles 2°, 3°, and 4°. The maximum tensile strength was reported to be 117 MPa and the macro hardness was reported to be 181 VH (in the nugget zone) at a tilt angle of 4°. The macro hardness was increased as the tilt angle increases from 0° to 4°. In addition to this, the thermo-mechanically affected zone (at the copper side) was found to be the weakest zone for a dissimilar copper–aluminum friction stir welding system.

17 October 2018 in Journal of Materials Research
Verified
Journal Article
Open access
PDF file
Kush MehtaKush Mehta
Kush Mehta
This article showcases details on enumerative information of dissimilar aluminum (Al) to steel welds manufactured using different friction-based welding processes with an emphasis on the description of the manufacturing process, influence of parameters, microstructural variations, formation of intermetallic compounds (IMCs), and variations in mechanical properties. Friction-based welding processes such as friction welding, friction stir welding, hybrid friction stir welding, friction stir spot welding, friction stir spot fusion welding, friction stir scribe welding, friction stir brazing, friction melt bonding, friction stir dovetailing, friction bit joining, friction stir extrusion, and friction stir assisted diffusion welding are analyzed for the formation of dissimilar Al–steel joints. It can be summarized that friction-based joining processes have great potential to obtain sound Al–steel joints. The amount of frictional heat applied decides the type and volume fraction of IMCs that subsequently affects mechanical joint properties. Process variations and novel process parameters can enhance joint properties.

1 January 2017 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
Kush MehtaKush Mehta
Kush Mehta
VBVishvesh J. Badheka
Vishvesh J. Badheka

1 May 2015 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
Kush MehtaKush Mehta
Kush Mehta
VBVishvesh Badheka
Vishvesh Badheka

1 November 2019 in Journal of Manufacturing Processes
Verified
Journal Article
Closed access
NPNirav P. Patel
Nirav P. Patel
PPParth Parlikar
Parth Parlikar
RDRahul Singh Dhari
Rahul Singh Dhari
Kush MehtaKush Mehta
Kush Mehta
MPMilap Pandya
Milap Pandya