Cenk Karakurt

Prof. Dr. Cenk Karakurt

orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 May 2014 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Closed access
PDF file
CKCenk Karakurt
Cenk Karakurt

20 September 2015 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
CKCenk Karakurt
Cenk Karakurt
YBYıldırım Bayazıt
Yıldırım Bayazıt
This study is based on determination of the freeze-thaw resistance of air-entrained and non-air-entrained normal strength concrete (NC) and high strength concrete (HSC) produced with fly ash and silica fume according to surface scaling. The procedure allows us to measure the amount of scaling per unit surface area due to a number of well defined freezing and thawing cycles in the presence of deicing salt. The weight loss, surface scaling, moisture uptake, and internal damage were measured after 0 and after every 4th freeze-thaw cycle. The test results showed that the freeze-thaw resistance is influenced directly by the compressive strength property of the concrete. Silica fume significantly reduced the resistance of normal strength concrete against freeze-thaw effect without plasticizing agent. The surface scaling of silica fume concrete without admixture was 22% higher than reference normal concrete.

27 February 2022 in Materials
Verified
Journal Article
Open access
PDF file
CKCenk Karakurt
Cenk Karakurt
MDMahmut Dumangöz
Mahmut Dumangöz
Self-compacting concrete (SCC) is a special, highly fluid type of concrete that is produced using chemical additives. It is easier to pour and reduces defects arising from workability. Waste marble dust is generated during the production of marble using different methods, or during the cutting of marble in processing plants; however, the uncontrolled disposal of waste marble dust in nature is associated with some environmental problems. Cement and concrete technology is a field with potential for the utilization of these large amounts of waste. The present study explores the use of marble dust (MD) (an industrial waste generated in abundance around the province of Bilecik) and granulated blast furnace slag (GBFS) (another industrial waste product) in the production of SCC. In this study, MD and GBFS are used as fine materials in SCC mixtures, and the rheological and workability properties and other hardened concrete properties of the produced SCC specimens are tested. Additional tests are conducted to identify the durability of the specimens to sulfate attack, as well as their freeze–thaw and abrasion resistance, followed by microstructure tests to identify the effects of MD and GBFS on bond structure. The late-age performances of MD and GBFS were then examined based on the results of the durability tests. The presented results revealed improvements in the fresh and hardened properties of SCC produced using MD and GBFS.


27 May 2025 in Advanced Powder Technology
Verified
Journal Article
Closed access
CKCenk Karakurt
Cenk Karakurt
AŞAhmet Ferdi Şenol
Ahmet Ferdi Şenol
NDNazım Çağatay Demiral
Nazım Çağatay Demiral

31 December 2022 in Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi
Verified
Journal Article
Open access
PDF file
MTMehmet Uğur Toprak
Mehmet Uğur Toprak
AŞAhmet Ferdi ŞENOL
Ahmet Ferdi ŞENOL
NDNazım Çağatay DEMİRAL
Nazım Çağatay DEMİRAL
CKCenk Karakurt
Cenk Karakurt
Bu çalışmada çevre kirliliğini azaltmak amacı ile pişmiş kil (tuğla, kiremit) ve mermer atığı tozları jeopolimer harç üretiminde hammadde olarak kullanılmıştır. Bu amaçla, jeopolimer harçların taze ve sertleşmiş özelliklerine hammadde kullanım oranının ve kür sıcaklığının (60 ve 80 ℃) etkileri incelenmiştir. Pişmiş kil tozu (%50) ve mermer tozu (%50) beraber kullanılarak hazırlanan jeopolimer harç, %100 kil tozu ile üretilene göre %40 fazla yayılma göstermiştir. Jeopolimer harçların 7 günlük basınç dayanımları, 28 günlük dayanımlarının yaklaşık %90’ına ulaşmıştır. En yüksek basınç dayanımı (28,50 MPa), %100 pişmiş kil tozu kullanılarak üretilen ve 80 ℃’ de kür uygulanan 28 günlük jeopolimer harçlarda görülmüştür.