In this paper, a novel negative refractive index metamaterial (NIM) is developed and characterized. The proposed metamaterial exhibits negative effective permittivity (ε_effe) and negative effective permeability (µ_effe) at millimeter wave frequency of 28 GHz. This attractive feature is utilized to enhance the gain of a microstrip patch antenna (MPA). Two thin layers of 5 × 5 subwavelength unit cell array of NIM are placed above a single MPA to enhance the gain of the antenna. Each unit cell has an area of 3.4 × 3.4 mm². A gain increase of 7.9 dBi has been observed when using the proposed NIM as a superstrate. Furthermore, the NIM array is placed over a 2 × 2 array of MPAs with four ports to demonstrate versatility of the metamaterial. The total size of the 2 × 2 antenna array system with N-MTM is about 61.1 × 34 × 16mm³(5.71λ × 3.18λ × 1.5λ, whereλis the free-space wavelength at 28 GHz). The measurement result indicate that the maximum gain of the antenna array is 13.5dBi. A gain enhancement of 7.55 dB in E-Plane and 7.25 dB in H-Plane at the resonant frequency of 28 GHz is obtained. The proposed antenna structure is suitable for 5G millimeter wave communications, in particular, for possible implementation in future millimeter wave access points and cellular base stations.

Novel designs of frequency selective surface (FSS) are presented for wideband applications in X, Ku and mmWave (millimeter Wave) bands. Two identical metallic layers of FSS are imprinted on both sides of the RO4003 substrate. The geometry parameters are optimized to maximize the bandstop at the specified in-band maximum transmission level of −10 dB; satisfaction of the latter condition is enforced through appropriate formulation and handling of the design constraints. The proposed structure is versatile and can be readily re-designed for various operating bands. For the sake of illustration, two instances of the FSS were developed. Design 1 exhibits broad bandstop of 9.8 GHz at the X- and Ku-bands, whereas the bandstop of Design 2 is 33.5 GHz at the mmWave band. The two FSS unit cell designs share the same base topology, but specific dimensions are adjusted to operate within the lower and the higher bands, respectively. The unit cell is symmetrical, therefore, ensures an excellent resonance stability performance with respect to different polarizations (TE and TM) and incidence angles. For proof of concept only FSS Design 1 is fabricated and measured in an anechoic chamber. The simulated and measured results exhibit good agreement. Extensive benchmarking against state-of-the-art FSS designs from the literature corroborates the advantages of the proposed topology in terms of design novelty, topological versatility, compact size, and wide bandstop response as compared to the previously available designs.

5G NR (new radio) introduces the concept of massive MIMO (multiple-input multiple-output) technology, in which a larger number of antenna arrays are installed on the transceiver. Due to the increased number of antenna elements allocated close to each other (approximately at a distance of half a wavelength), mutual coupling becomes a serious problem leading to performance degradation of the MIMO communication system. In this communication, two different configurations of closely spaced antenna array elements are studied. In order to reduce the mutual coupling, a combination of a metamaterial-based frequency-selective surface (FSS), a metallic strip, and a slot element in the ground plane is examined. It is found that the proposed technique significantly suppresses mutual coupling from −12 dB to −25 dB. Both designs are fabricated and experimentally validated. The simulation results are in good agreement with the measurements. The proposed mutual coupling reduction technique may be suitable for massive MIMO systems in fifth-generation (5G) new radio applications.

This paper presents a compact tri-band omnidirectional antenna designed for CubeSat applications, operating at UHF (0.755 GHz), L-band (1.25 GHz), and S-band (2.28–3.74 GHz). The antenna features a defected ground structure (DGS) and metallic vias, which enhance impedance matching and enable stable multi-band resonance while maintaining a small footprint of 0.26λ × 0.26λ × 0.013λ within a 1U CubeSat. Unlike conventional CubeSat antennas that require external deployment, the proposed design is fully enclosed within the CubeSat, ensuring easy integration and mechanical robustness. The antenna exhibits omnidirectional radiation patterns across all frequency bands, making it suitable for reliable satellite-ground communication. The measured results confirm a high radiation efficiency exceeding 90%, and strong agreement between simulated and experimental results. The combination of compact size, multi-band operation, and high efficiency makes this antenna an ideal candidate for next-generation CubeSat communication systems.