David Berstad

Mr. David Berstad


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2019 in Energies
Verified
Journal Article
Open access
PDF file
SGStefania Osk Gardarsdottir
Stefania Osk Gardarsdottir
ELEdoardo De Lena
Edoardo De Lena
MRMatteo Romano
Matteo Romano
Simon RoussanalySimon Roussanaly
Simon Roussanaly
MVMari Voldsund
Mari Voldsund
Giovanni CintiGiovanni Cinti
Giovanni Cinti
This paper presents an assessment of the cost performance of CO2 capture technologies when retrofitted to a cement plant: MEA-based absorption, oxyfuel, chilled ammonia-based absorption (Chilled Ammonia Process), membrane-assisted CO2 liquefaction, and calcium looping. While the technical basis for this study is presented in Part 1 of this paper series, this work presents a comprehensive techno-economic analysis of these CO2 capture technologies based on a capital and operating costs evaluation for retrofit in a cement plant. The cost of the cement plant product, clinker, is shown to increase with 49 to 92% compared to the cost of clinker without capture. The cost of CO2 avoided is between 42 €/tCO2 (for the oxyfuel-based capture process) and 84 €/tCO2 (for the membrane-based assisted liquefaction capture process), while the reference MEA-based absorption capture technology has a cost of 80 €/tCO2. Notably, the cost figures depend strongly on factors such as steam source, electricity mix, electricity price, fuel price and plant-specific characteristics. Hence, this confirms the conclusion of the technical evaluation in Part 1 that for final selection of CO2 capture technology at a specific plant, a plant-specific techno-economic evaluation should be performed, also considering more practical considerations.

12 February 2019 in Energies
Verified
Journal Article
Open access
PDF file
MVMari Voldsund
Mari Voldsund
SGStefania Osk Gardarsdottir
Stefania Osk Gardarsdottir
ELEdoardo De Lena
Edoardo De Lena
JCJosé Francisco Pérez Calvo
José Francisco Pérez Calvo
AJArmin Jamali
Armin Jamali
KJKristin Jordal
Kristin Jordal
A technical evaluation of CO2 capture technologies when retrofitted to a cement plant is performed. The investigated technologies are the oxyfuel process, the chilled ammonia process, membrane-assisted CO2 liquefaction, and the calcium looping process with tail-end and integrated configurations. For comparison, absorption with monoethanolamine (MEA) is used as reference technology. The focus of the evaluation is on emission abatement, energy performance, and retrofitability. All the investigated technologies perform better than the reference both in terms of emission abatement and energy consumption. The equivalent CO2 avoided are 73–90%, while it is 64% for MEA, considering the average EU-28 electricity mix. The specific primary energy consumption for CO2 avoided is 1.63–4.07 MJ/kg CO2, compared to 7.08 MJ/kg CO2 for MEA. The calcium looping technologies have the highest emission abatement potential, while the oxyfuel process has the best energy performance. When it comes to retrofitability, the post-combustion technologies show significant advantages compared to the oxyfuel and to the integrated calcium looping technologies. Furthermore, the performance of the individual technologies shows strong dependencies on site-specific and plant-specific factors. Therefore, rather than identifying one single best technology, it is emphasized that CO2 capture in the cement industry should be performed with a portfolio of capture technologies, where the preferred choice for each specific plant depends on local factors.

12 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
DBDavid Berstad
David Berstad
GSGeir Skaugen
Geir Skaugen
Simon RoussanalySimon Roussanaly
Simon Roussanaly
RARahul Anantharaman
Rahul Anantharaman
PNPetter Nekså
Petter Nekså
TGTruls Gundersen
Truls Gundersen
Capture conditions for CO2 vary substantially between industrial point sources. Depending on CO2 fraction and pressure level, different capture technologies will be required for cost- and energy-efficient decarbonisation. For decarbonisation of shifted synthesis gas from coal gasification, several studies have identified low-temperature CO2 capture by condensation and phase separation as an energy- and cost-efficient option. In the present work, a process design is proposed for low-temperature CO2 capture from an Integrated Gasification Combined Cycle (IGCC) power plant. Steady-state simulations were carried out and the performance of the overall process, as well as major process components, were investigated. For the baseline capture unit layout, delivering high-pressure CO2 at 150 bar, the net specific power requirement was estimated to 273 kJe/kgCO2, and an 85% CO2 capture ratio was obtained. The impact of 12 different process parameters was studied in a sensitivity analysis, the results of which show that compressor and expander efficiencies, as well as synthesis gas separation temperature, have the highest impact on power requirements. Modifying the process to producing cold liquid CO2 for ship transport resulted in 16% increase in net power requirements and is well suited for capturing CO2 for ship transport.

7 December 2021 in Energies
Verified
Journal Article
Open access
PDF file
STStian Trædal
Stian Trædal
JSJacob Hans Georg Stang
Jacob Hans Georg Stang
ISIngrid Snustad
Ingrid Snustad
MJMartin Viktor Johansson
Martin Viktor Johansson
DBDavid Berstad
David Berstad
For vessel-based transport of liquid CO2 in carbon capture and storage chains, transport at 8 bar(a) enable significant cost reductions compared to transport at higher pressures for most transport distances and volumes. Transport at even lower pressures could further reduce the costs. There are, however, concerns related to dry ice formation and potential clogging in parts of the chain that could lead to operational issues when operating close to the triple point pressure of CO2. In this paper, results from an experimental campaign to de-risk and gain operational experience from the low-pressure CO2 liquefaction process are described. Six experiments using pure CO2 or CO2/N2 mixtures are presented. In four of the experiments, the liquid product pressure was continuously lowered until dry ice was detected and eventually clogged the system. In the final two experiments, the liquefaction process was run in steady-state at low liquefaction pressures for five hours to ensure that there is no undetected dry ice in the process that could lead to accumulation and operational issues over time. These experiments demonstrate that pure CO2 can be safely liquefied at 5.8 bar(a) and a CO2/N2 mixture can be liquefied at 6.5 bar(a) without issues related to dry ice formation.

1 April 2023 in Carbon Capture Science & Technology
Verified
Journal Article
Open access
DBDavid Berstad
David Berstad
TGTruls Gundersen
Truls Gundersen

23 February 2024 in Energies
Verified
Journal Article
Open access
PDF file
DBDavid Berstad
David Berstad
JSJulian Straus
Julian Straus
TGTruls Gundersen
Truls Gundersen
Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved through oxygen-blown autothermal reforming as the core technology, combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide, and methane. The low-temperature tail gas separation section is presented in detail. The main objective of the paper is to study and quantify the exergy efficiency of this separation process in detail. To achieve this, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4·10−7. The exergy efficiency of the CO2 capture process is calculated, based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process.