Energy harvesting from piezoelectric materials is quite common and has been studied for the past few decades. But recently, there have been a lot of new advancements in harnessing energy via piezoelectric materials. In this regard, several studies were carried out in analytical chemistry. This paper provides a detailed review of different piezoelectric materials, their structures, their fabrication processes, and their applications in analytical chemistry. Detection of the various gases percentage in ambient air is a valuable analytical chemistry technique. Additionally, the benefits of using piezoelectric materials, i.e., crystal for gas and liquid chromatography, virus detection including COVID-19 virus detection, water determination, trace metal analysis and the ability to measure micro weights with quartz crystal with some other applications are also described in this review. Energy harvesting is incredibly important and must be implemented on a large scale. So, developing self-powering devices can resolve the problems, and piezoelectric materials are gaining interest day by day because these materials help in energy generation.

High-speed machining is considered to be a promising machining technique due to its advantages, such as high productivity and better product quality. With a paradigm shift towards sustainable machining practices, the energy consumption analysis of high-speed machining is also gaining ever-increasing importance. The current article addresses this issue and presents a detailed analysis of specific cutting energy (SCE) consumption and product surface finish (Ra) during conventional to high-speed machining of Al 6061-T6. A Taguchi-based L16 orthogonal array experimental design was developed for the conventional to high-speed machining range of an Al 6061-T6 alloy. The analysis of the results revealed that SCE consumption and Ra improve when the cutting speed is increased from conventional to high-speed machining. In particular, SCE was observed to reduce linearly in conventional and transitional speed machining, whereas it followed a parabolic trend in high-speed machining. This parabolic trend indicates the existence of an optimal cutting speed that may lead to minimum SCE consumption. Chip morphology was performed to further investigate the parabolic trend of SCE in high-speed machining. Chip morphology revealed that the serration of chips initiates when the cutting speed is increased beyond 1750 m/min at a feed rate of 0.4 mm/rev.

Solar light absorber surface is probably one of the most important components in solar still that dictates the distillate yield. In this work, a systematic study is conducted to investigate the effect of particle size and concentration of titanium oxide (TiO₂) in black paint in increasing the solar still absorber surface temperature. The various available particle sizes, i.e., 20, 150, and 400 nm, are mixed in black paint with varying concentrations and are applied on the absorber plate. XRD is used for phase identification of as-received powders. UV-Vis spectroscopy is used to examine light absorption properties. Finally, extensive indoor testing (using an improvised solar simulator) and outdoor testing are conducted to optimize the concentration. An increase in surface temperature is observed with the introduction of TiO₂ nanoparticles in black paint. Furthermore, the increase in particle size leads to an increase in temperature. The highest surface temperatures of 104.86°C, 105.42°C, and 106.32°C are recorded for specimens with particles sizes 20 nm (at 15 wt% concentration), 150 nm (at 10 wt% concentration), and 400 nm (at 7 wt% concentration), respectively. Furthermore, the highest temperature of 69.69°C is recorded for TiO₂-400 nm specimens under outdoor conditions, which is 15.97% higher than that of the bare aluminum plate. The increase in surface temperature may be due to high UV absorption. Moreover, an increase in particle size leads to high light-scattering ability, further improving the light-harvesting ability.

Aluminum metal matrix composites (AMMCs) have become increasingly ubiquitous in the fields of aerospace and automobile businesses due to their lightweight properties. Their machining is a challenging task because of the presence of supplemented particles, also called reinforcements. As the wt% of the supplemented particles changes, the morphological and machining behaviors of the AMMCs change. The present work is focused on exploring the thermo-mechanical properties of AMMCs which would help in AMMC applications in the aerospace industry with a new collection of composites containing silicon carbide (SiC) and zircon/zirconium silicate (ZrSiO₄) as supplements in wt% of 5%, 20%, 30%, and 40%. Uniform binary and hybrid sample pallets are prepared by powder metallurgy (PM). The said samples are sintered and then machined using wire electric discharge machining (WEDM) employing brass wire with a feed rate of 2 to 3 mm/min. Also, analysis of porosity and recast layer formation is performed via the microstructure, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS). Some interesting and useful findings are obtained which can extend the applications of AMMCs in automobiles and the aerospace industry. The results reveal that temperature and wt% are playing their significant roles in the changes in the thermo-mechanical properties of AMMCs. Mathematical equations via regression analysis using Minitab 17 and Excel are developed for the congruence of experimental data. Analysis of Variance (ANOVA) is also performed. Hence, the most optimized relationships for the best machining output are established and presented in this proposed study.