In this study, low cost waste chicken fat (WCF) feedstock was used for fuel-like hydrocarbon production. The effects of varying reaction parameters on the hydrocracking of waste chicken fat using NiW/SiO2–Al2O3 catalyst were investigated. The reactions were carried out in a fixed bed down flow reactor at reaction temperatures of 400–450°C, liquid hourly space velocity (LHSV) of 1, 2, 4h−1, H2/oil molar ratio of 450 v/v and hydrogen pressures of 6.0MPa. The effects on hydrocracking conversion and distribution of products were investigated. The liquid product was analyzed using gas chromatography (GC) to quantify n-alkanes. Hydrocracking conversion and organic liquid products (OLPs) were evaluated by ASTM D-2887 distillation. The results showed that the catalytic hydrocracking of WCF generates fuels that have chemical and physical properties comparable to those specified for petroleum-based fuels. The amount of kerosene/diesel fractional product decreased with an increase in the temperature and a decrease in the LHSV; while gasoline like petroleum fuel increased. A considerable elimination of O2 from chicken waste fat molecules has been indicated by FTIR analysis. The oxygen removal pathway of WCF over NiW/SiO2–Al2O3 catalyst is primarily carried out by hydro-deoxygenation. The reaction was found to follow the second order mechanism, and the estimated activation energy Ea was 96kJmol−1. The exploited catalyst was employed in another run where the results showed the catalyst stability and can be used for several times
1 July 2017 in Refractories and Industrial Ceramics
The current study applies the eco-friendly principle of “wastes treat wastes”. By swift methods, a composite photocatalyst was prepared from waste-extracted oxides, namely V2O5, Ag, and ZnO. The metal–lixiviant complexes were used as metal precursors, where the lixiviants act as auto-templates and increase the compatibility between the mixed metallic species, and their controlled thermal removal generates pores. The tri-constitute composite catalyst was doped with nitrogen. The constitution, surface composition, and optical properties of the doped catalysts were investigated by XRD, SEM, TEM, BET surface analysis, XPS, diffuse reflectance, and PL spectra. The as-prepared catalysts were employed in the photodegradation of Congo red dye (CR) under visible irradiation at ambient temperature. The degree of Ag dispersion had a significant effect on the bandgap, as did metal and metal-nonmetal co-doping. The efficiency of dye removal changes dramatically with time up to 120 min, after which it begins to decrease. According to the pH effect, the normal pH of Congo red dye (6.12) is optimal. At a catalyst dose of 1 g L−1 and an irradiation period of 120 min, photodegradation efficiency reached 89.9% and 83.4% over [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively. The kinetic study depicted the significant role of mass transfer in the reaction rate. The obtained rate constants were 0.995 mole L−1 S−1 and 0.998 mole L−1 S−1 for [Ag0.05 ZnO0.05 V2O5(0.90)] and [Ag0.05 ZnO0.05 V2O5(0.90)]N, respectively.
1 February 2016 in Journal of the Taiwan Institute of Chemical Engineers
A cost-effective adsorbent was prepared by carbonization of pre-treated Phragmites australis reed at 500 °C. Phragmites australis was characterized using Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) with energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) surface analyses. XRD of the as-prepared adsorbent exhibited a partially crystalline structure with a specific surface area of 211.6 m2/g and an average pore diameter of 4.2 nm. The biosorption potential of novel biosorbent Phragmites australis reed was investigated with a batch scale and continuous flow study. The study was conducted at different constraints to obtain optimum pH conditions, adsorbent dose, contact time, agitation speed, and initial TDS concentration. In order to analyze the properties of the procedure and determine the amount of sodium removal, Langmuir, Freundlich, and Dubinin–Radushkevich isotherms were tested. The optimal values of contact time, pH, and adsorbent dose were found to be 150 min, 4, and 10 g/L, respectively, with an agitation speed of 300 rpm at room temperature (27 °C). The three tested isotherms show that the adsorption of Na+ onto the prepared adsorbent is a hybrid process from physi- and chemisorption. For industrial application, the adsorbent was tested using the adsorbent column technique. Pseudo-first-order, pseudo-second-order, and diffusion models were connected, and it was discovered that the information fit best to the pseudo-second-arrange active model. According to the intraparticle diffusion model, the mechanism goes through four stages before reaching equilibrium. The periodicity test shows that the adsorption ability of Phragmites australis can be recovered by washing with 0.1 M HCl.