The commercialization of lithium–sulfur batteries is seriously affected by the shuttle behavior and slow conversion kinetics of polysulfides. Herein, a new porous organic polymer (POP) is synthesized and grown on reduced graphene oxide (rGO) in situ to improve battery performance, which serves as an efficient polysulfide adsorber and catalytic promoter for polysulfide conversion. The polar POP shows strong chemisorption to polysulfides, which is confirmed by a series of calculations and experimental results. As a popular conductive substrate, rGO offers an electron transport channel for sulfur and polysulfide conversion. Due to the synergistic functions of composite materials, the batteries with POP@rGO modified separators retain a high specific capacity of 697.3 mA h g−1 and a minimum capacity fading rate of 0.04% per cycle at 1C over 500 cycles. Besides, even at a high sulfur loading of 5 mg cm−2, a high area capacity of 4.27 mA h cm−2 can also be achieved, which shows that it has great potential in promoting the commercialization of lithium–sulfur batteries.
The practical application of lithium–sulfur battery is seriously limited by the loss of active substances and the deterioration of cycle stability caused by the ‘shuttle effect’ of lithium polysulfides (LiPSs). In this work, graphene oxide (GO) coated covalent organic framework (COF) compound materials were synthesized as sulfur host material in spray-drying process. The polar groups on COF can efficiently adsorb LiPSs through lithiophilic interaction, which can reduce the ‘shuttle effect’ caused by soluble LiPSs. Besides, GO in the outer layer can wrap discrete sulfur to reduce the loss of active substances, which further improves the cycle stability of the cathode. The COF@GO/S cathode exhibits a high initial specific capacity of 848.4 mAh g −1 and retains a capacity of 601.1 mAh g −1 after 500 cycles at 1 C counting with a low capacity fading of 0.058% per cycle.
The development of solid-state polymer electrolytes is an effective way to overcome the notorious shuttle effect of polysulfides in traditional liquid lithium sulfur batteries. In this paper, cationic cyclopropenium based cross-linked polymer was firstly prepared with the one pot method, and then the counter ion was replaced by TFSI− anion using simple ion replacement. Cationic cyclopropenium hyper-crosslinked polymer (HP) was introduced into a polyethylene oxide (PEO) matrix with the solution casting method to prepare a composite polymer electrolyte membrane. By adding HP@TFSI to the PEO-based electrolyte, the mechanical and electrochemical properties of the solid-state lithium-sulfur batteries were significantly improved. The PEO-20%HP@TFSI electrolyte shows the highest Li+ ionic conductivity at 60 °C (4.0 × 10−4 S·cm−1) and the highest mechanical strength. In the PEO matrix, uniform distribution of HP@TFSI inhibits crystallization and weakens the interaction between each PEO chain. Compared with pure PEO/LiTFSI electrolyte, the PEO-20%HP@TFSI electrolyte shows lower interface resistance and higher interface stability with lithium anode. The lithium sulfur battery based on the PEO-20%HP@TFSI electrolyte shows excellent electrochemical performance, high Coulombic efficiency and high cycle stability. After 500 cycles, the capacity of the lithium-sulfur battery based on PEO-20%HP@TFSI electrolytes keeps approximately 410 mAh·g−1 at 1 C, the Coulomb efficiency is close to 100%, and the cycle capacity decay rate is 0.082%.
In the development of lithium–sulfur batteries (LiSBs), the irreversible volume changes, annoying shuttle effect and slow conversion kinetics of lithium polysulfides (LiPSs) are the main obstacles for further commercialization. Therefore, a rational design of a multifunctional sulfur cathode is essential to broaden the application of LiSBs, namely, using a squaraine-linked porous organic framework as the cathode by means of anchoring Co(II) ions into the polar site of the porous structure. The as-obtained Co-HUT4 material maintains an abundant pore structure to house sulfur and gives physical confinement to LiPSs. Besides, the well-dispersed cobalt(II) ions provide good chemical capture sites and catalytic activity, helping to suppress the shuttling effect and enhance the adsorption and conversion of LiPSs. Benefitting from these multifunctional characteristics, LiSBs based on the Co-HUT4 electrode exhibit an exceptional stability of 650 mA h g−1 after 500 cycles at 1.0C, and a specific capacity of 740 mA h g−1 can also be realized with a high sulfur loading (5.5 mg cm−2), which shows remarkable potential for LiSBs.