Erosive wear due to the fact of sand severely affects hydrocarbon production industries and, consequently, various sectors of the mineral processing industry. In this study, the effect of the elbow geometrical configuration on the erosive wear of carbon steel for silt–water–air flow conditions were investigated using material loss analysis, surface roughness analysis, and microscopic imaging technique. Experiments were performed under the plug flow conditions in a closed flow loop at standard atmospheric pressure. Water and air plug flow and the disperse phase was silt (silica sand) with a 2.5 wt % concentration, and a silt grain size of 70 µm was used for performing the tests. The experimental analysis showed that silt impact increases material disintegration up to 1.8 times with a change in the elbow configuration from 60° to 90° in plug flow conditions. The primary erosive wear mechanisms of the internal elbow surface were sliding, cutting, and pit propagation. The maximum silt particle impaction was located at the outer curvature in the 50° position in 60° elbows and the 80° position in 90° elbows in plug flow. The erosion rate decreased from 10.23 to 5.67 mm/year with a change in the elbow angle from 90° to 60°. Moreover, the microhardness on the Vickers scale increased from 168 to 199 in the 90° elbow and from 168 to 184 in the 60° elbow.
The article presents the results of measurements carried out for the 3D Kreator Motion printer table in terms of analysis of impact of mechanical vibrations on print quality. The article presents an analysis of the mechanical vibrations in the plane perpendicular to the surface of the table. The measurements were obtained using laser measurement techniques.
Pre-sowing laser light stimulation is a method commonly used to increase the productivity of legume species. However, it has not been proved that single-laser light stimulation is a more effective technique for enhancing plant productivity and seed yield quality than using different laser lights in sequence, by which means synergistic relations are produced. A two-year, single-factor field experiment was performed in order to test selected combinations of light stimulation of soybean seeds, the effectiveness of which would be expressed as increased plant yield and improved quality parameters. Pre-sowing light stimulation of soybean seeds was shown to significantly influence the morphological traits of the plants. It significantly increased pod number, pod weight, seed number, and seed weight compared to the control. Coherent laser light stimulation of soybean seeds with a helium–neon laser and with an argon laser increased soybean yields by 30% on average compared to the control. The ratio of the yield from the main shoot to the yield from the lateral branches in this treatment was 40:60, indicating that pre-sowing stimulation of seeds had a significant and positive effect by increasing the yield of the lateral branches relative to the control. Stimulation of seeds (3 × 3 s) with a helium–neon laser significantly increased protein content in soybean seeds, on average by 11% compared to the control. A longer duration of pre-sowing stimulation of seeds (3 × 9 s) resulted in a significant increase in crude fat content in the seeds by an average of 5% compared to the control. The use of physical light stimulation on soybean seeds is a promising solution for increasing soybean yields.
This paper focuses on magnetorheological clutches (MR clutches) with a disc structure that can be designed as one-disc or multi-disc clutches (number of discs: N = 1, N > 2). The main goal of the paper is to compare their overall dimensions (lengths and radii), masses, volumes, and characteristic factors—torque per mass ratio and torque per volume ratio for MR clutches that develop the same given clutching torque but differ in the number of discs (it is assumed that the number of discs of the primary member varies from one to four). This analysis develops charts and guidelines that will allow designers to choose the appropriate number of discs from the view point of various criteria, and with various limitations regarding geometry, geometric proportions, mass, volume, or restrictions on the amount of active materials used in the manufacturing process. The limitations on the active materials used are of particular importance in the case of mass production. Our methodology uses a comparative study, which can also be used when comparing design solutions of other electromechanical converters.
The paper is focused on magnetorheological (MR) clutches applied in industrial drive systems working in a steady continuous-duty state. The main goal of the carried out numerical and analytical analyses oriented towards electrical power consumption, copper losses (Joule heat) in an excitation coil, spatial temperature distributions and the highest temperature possible for an MR fluid is to compare MR clutches due to a different number of discs. The authors considered selected representative MR multi-disc clutches with one, two, three or four discs, developing clutching torque equal to 20, 35 and 50 Nm. These clutches were constructed based on the in-house design that integrates analytical and field methods (further in the paper referred to as the integrated analytical-field design method) described in the literature. The thermal computer simulation results obtained with the help of the AGROS2D program, combined with findings achieved with the use of simplified physical reasonings, allow one to draw the conclusion that the most advantageous, recommended number of discs for a magnetorheological clutch from the viewpoint of various (both constructional and thermal) criteria is the number of discs: N = 2. This conclusion takes into account the results presented earlier in the literature: the choice is a compromise between decreasing the mass (volume) of the MR clutches and increasing both the electrical power consumption and the maximum temperature of MR fluids in a clutch working region as the number of discs, N, increases.