Gang Liu

Gang Liu


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 May 2022 in Crystals
Verified
Journal Article
Open access
PDF file
GLGang Liu
Gang Liu
JYJie Yang
Jie Yang
LZLiqiang Zhang
Liqiang Zhang
QGQiuge Gao
Qiuge Gao
LQLong Qian
Long Qian
RZRongyao Zhang
Rongyao Zhang
Honeycomb composites (HCs) are diversely employed in aerospace, national defense and other fields owing to their remarkable spatial geometry and excellent mechanical properties. Their complex hexagonal cell structure and heterogeneous material properties cause major problems when implementing high-quality processing. Surface defects generated by processing will reduce the capability and service lifespan of the honeycomb sandwich structure. Therefore, the high quality of HCs is a topic of close attention for researchers. In this paper, the consequences of different cutting parameters of rotary ultrasonic machining (RUM) on surface quality with an ultrasonic circular knife (UCK) were studied through multiple groups of single-factor and orthogonal experiments with two-factors/four-levels and one-factor/three-levels. The single factor experiment was used to explain the effect that the degree of cutting parameters has on surface quality, and the orthogonal experiments were applied to explain the interaction between the processing parameters and the influence law of each factor on surface quality. Therefore, the reasonable cutting parameters of HCs were determined through experimental results to provide guidance for the realization of the precise and efficient machining of HCs. This study can provide a basis for the subsequent comprehensive consideration of various factors to achieve high-quality machining of HCs.

27 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
BQBo Qian
Bo Qian
HFHongri Fan
Hongri Fan
GLGang Liu
Gang Liu
JZJianrui Zhang
Jianrui Zhang
PLPei Li
Pei Li
A microchannel radiator is advantageous due to its high efficiency and large boiling heat transfer coefficient of two-phase flow. Based on the research of uniform lattice structures, this study proposed a microchannel heat exchanger with a nonuniform lattice structure. The calculation, optimal formation, and boiling heat transfer performance of the nonuniform lattice structure based on selective laser melting (SLM) were investigated, and heat exchange samples were successfully prepared using SLM. The porosity and pore morphology of the samples were analysed, and the contrast experiments of boiling heat transfer were conducted with deionised water. The results revealed that the heat flow density of the lattice structure was a minimum of 244% higher than that of the traditional liquid-cooled plate. The critical heat flux density of the lattice structure is 110 W∙cm−2, and the critical heat flux density of the traditional flat plate is 45 W∙cm−2. In addition, the effects of cell structures indicated that for frame cells, the heat transfer effect of nonuniform frames was inferior to that of uniform frames; for face-centred cubic (FCC) cells, the nonuniform and uniform frames exhibited the same trend. However, the heat flow density of FCC cells was 25% higher than that of frame structures.

24 July 2021 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
JLJunli Li
Junli Li
ZHZiru Huang
Ziru Huang
GLGang Liu
Gang Liu
QAQinglong An
Qinglong An
MCMing Chen
Ming Chen

29 October 2021 in Metals
Verified
Journal Article
Open access
PDF file
BQBo Qian
Bo Qian
HFHongri Fan
Hongri Fan
GLGang Liu
Gang Liu
JZJianrui Zhang
Jianrui Zhang
PLPei Li
Pei Li
The additive manufacturing technology of laser-based powder bed fusion (L-PBF), which is used to produce boiling heat transfer structures, offers a high processing flexibility and can provide lattice structures with a high surface-to-volume ratio. As an important part of the phased array radar, the plentiful transmit/receive (T/R) modules can generate considerable heat. Targeting this local overheating problem, this study discusses the pass design, the optimal formation process, and boiling heat transfer performance of microchannel liquid-cooled plates based on L-PBF additive manufacturing technology. The optimum design and process parameters were obtained by performing basic channel experiments. On this basis, the design and formation experiments of the microchannel structure were performed, and then the porosity and pore morphology of microchannel liquid-cooled plate samples were analysed. The boiling heat transfer experiments were conducted with deionised water, and the boiling heat transfer characteristics were compared with the saturated boiling curve of a traditional copper-tube liquid-cooled plate. The average wall temperature of the designed samples decreased by 4% compared with that of the traditional liquid-cooled plate under the same heat flow density the value reduced from 111.9 °C to 108.2 °C. Furthermore, within the same optimal boiling temperature range, the average heat flow densities of all the prepared samples increased by >60% compared with those of the traditional liquid-cooled plate the value increased from minimum 16 W∙cm−2 to maximum 34 W∙cm−2. The self-supporting microchannel structure can considerably improve the heat dissipation effect of T/R modules and solve the local overheating problem.

24 January 2025 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
MZMan Zhao
Man Zhao
LLLihao Li
Lihao Li
ZZZhihui Zhang
Zhihui Zhang
GLGang Liu
Gang Liu
LZLiqiang Zhang
Liqiang Zhang
Steven Yuehsan LiangSteven Yuehsan Liang
Steven Yuehsan Liang
During micro-grinding, multiple abrasive grains on grinding wheel circulate on the workpiece causing alternating mechanical and thermal loads which result in microstructure evolution. The microstructure evolution affects the flow stress of the material, which in turn affects force and temperature. This paper thoroughly investigates the cyclic iterative mechanism and proposes an analytical model to predict micro-grinding-induced residual stress. In this investigation, the flow stress model is developed considering temperature, strain, strain rate, yield stress, and material microstructure evolution, based on which, the micro-grinding force and temperature are calculated. On the basis, the evolution of grain size and phases transformation induced by force and temperature are calculated, in turn affected grinding force by flow stress. Then, the analytical model of residual stress is proposed incorporating the stresses induced by mechanical and thermal loadings as well as microstructure evolution. Moreover, the elastic or plastic deformation is determined according to Von-Mises criterion with the developed plastic modulus model in the stress relaxation process. Finally, the residual stress is measured to validate the improved iterative model. By comparing the traditional models, the results indicated that the developed cyclic iterative model obtains a higher accurate prediction of residua stress.

20 July 2023 in Fibers and Polymers
Verified
Journal Article
Closed access
PDF file
LXLihong Xu
Lihong Xu
CNCan Ni
Can Ni
GLGang Liu
Gang Liu
JLJunli Li
Junli Li