Bo Qian

Prof. Bo Qian

orcid

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 August 2019 in Royal Society Open Science
Verified
Journal Article
Open access
YGYang Gao
Yang Gao
XFXiaoliang Fang
Xiaoliang Fang
DTDanhquang Tran
Danhquang Tran
KJKuan Ju
Kuan Ju
BQBo Qian
Bo Qian
LJLi Jin
Li Jin
Dielectric elastomer actuator (DEA) based on dielectric elastomer holds promising applications in soft robotics. Compliant electrodes with large stretchability and high electrical conductivity are the vital components for the DEAs. In this study, a type of DEA was developed using carbon nanotube/polyvinyl alcohol (CNT/PVA) hydrogel electrodes. The CNT/PVA hydrogel electrodes demonstrate a stretchability up to 200% with a small relative resistance change of approximately 1.2, and a self-healing capability. The areal strain of the DEA based on the CNT/PVA hydrogel electrodes is more than 40%, much higher than the ones based on pure PVA electrodes.

12 May 2022 in Case Studies in Thermal Engineering
Verified
Journal Article
Open access
LZLihao Zhang
Lihao Zhang
BQBo Qian
Bo Qian
CZChaorui Zhang
Chaorui Zhang
JMJian Mao
Jian Mao
HFHongri Fan
Hongri Fan

4 October 2011 in Rapid Prototyping Journal
Verified
Journal Article
Closed access
BQBo Qian
Bo Qian
ZLZhang Lichao
Zhang Lichao
SYShi Yusheng
Shi Yusheng
GLGuocheng Liu
Guocheng Liu
Purpose: In stereolithgraphy rapid prototyping, the support can constrain the model deformation and avoid a lot of problems such as collapse, shift, and imbalance of the model. The support automatic generation algorithm has become the key research of rapid prototyping technics software; however, presently the efficiency of support automatic generation algorithm is low, and its algorithm is complex. Thus, it is of great importance in improving the overall efficiency of rapid prototyping technics software through enhancing the support generation efficiency. This paper aims to address these issues.Design/methodology/approach: Based on this, this paper proposes a discrete‐marking support algorithm for treatment of processing on manufactured part model of all triangle‐based discrete‐marking on the support plane, which realizes the three‐dimensional computation of intersection for each line associated with the triangle automatically, and avoid invalid computation between all the support lines and other triangles.Findings: The algorithm efficiency has reachedO(n). Meanwhile, the technics support generation speed has been improved. Furthermore, the new mesh discrete‐marking and automatic support generation algorithm has been successfully applied to the sterolithography apparatus and selective laser melting of HRPS series.Practical implications: Practical application indicates that the new support generation algorithm based on discrete‐marking considerably improves the support technics efficiency and stereolithgraphy rapid prototyping efficiency of the technics software.Originality/value: The research presents a Noval support fast generation algorithm based on discrete‐marking in stereolithgraphy rapid prototyping.

27 November 2021 in Materials
Verified
Journal Article
Open access
PDF file
BQBo Qian
Bo Qian
HFHongri Fan
Hongri Fan
GLGang Liu
Gang Liu
JZJianrui Zhang
Jianrui Zhang
PLPei Li
Pei Li
A microchannel radiator is advantageous due to its high efficiency and large boiling heat transfer coefficient of two-phase flow. Based on the research of uniform lattice structures, this study proposed a microchannel heat exchanger with a nonuniform lattice structure. The calculation, optimal formation, and boiling heat transfer performance of the nonuniform lattice structure based on selective laser melting (SLM) were investigated, and heat exchange samples were successfully prepared using SLM. The porosity and pore morphology of the samples were analysed, and the contrast experiments of boiling heat transfer were conducted with deionised water. The results revealed that the heat flow density of the lattice structure was a minimum of 244% higher than that of the traditional liquid-cooled plate. The critical heat flux density of the lattice structure is 110 W∙cm−2, and the critical heat flux density of the traditional flat plate is 45 W∙cm−2. In addition, the effects of cell structures indicated that for frame cells, the heat transfer effect of nonuniform frames was inferior to that of uniform frames; for face-centred cubic (FCC) cells, the nonuniform and uniform frames exhibited the same trend. However, the heat flow density of FCC cells was 25% higher than that of frame structures.

3 July 2024 in International Polymer Processing
Verified
Journal Article
Closed access
BLBiaoqiang Liu
Biaoqiang Liu
BQBo Qian
Bo Qian
ZHZhentao Hu
Zhentao Hu
YLYuxin Liang
Yuxin Liang
HFHongri Fan
Hongri Fan
In response to the problems of 3D printing, such as uneven wire discharge and easy clogging of printing nozzles in FDM (Fused Deposition Modeling) printing technology, this paper develops a screw extrusion 3D printing melting deposition system based on simulation. The simulation results show that the maximum deformation of the screw occurs at the tail end, with a maximum value of 0.04 mm, while the fluid pressure and the pressure on the surface of the screw gradually increase along the direction of extrusion, and the maximum pressure occurs near the nozzle, with a value of 0.13 MPa. The fluid pressure is positively correlated with the screw speed and negatively correlated with the screw pitch. The fitting formula is obtained by numerical simulation of the screw speed and the flow velocity at the nozzle outlet. Using a self-made screw extrusion 3D printing equipment, relevant experiments are conducted to explore the influence of different layer thicknesses and line spacings on the mechanical properties of printed samples, as well as the influence of printing speed on surface quality. It is found that layer thickness has a significant impact on the bending strength of printed samples, with a maximum value of 24.74 MPa and a minimum of 19.21 MPa. The bending strength decreases by 28.79 % from 0.6 mm to 1.0 mm layer thickness. The line spacing has a significant impact on the tensile strength of printed samples, with a maximum value of 27.22 MPa and a minimum of 21.16 MPa. As the printing speed increases, the surface roughness of the printed piece also gradually increases from Ra = 389.28 μm at v = 30 mm/s to Ra = 535.45 μm at v = 70 mm/s, an increase of 37.55 %.

29 October 2021 in Metals
Verified
Journal Article
Open access
PDF file
BQBo Qian
Bo Qian
HFHongri Fan
Hongri Fan
GLGang Liu
Gang Liu
JZJianrui Zhang
Jianrui Zhang
PLPei Li
Pei Li
The additive manufacturing technology of laser-based powder bed fusion (L-PBF), which is used to produce boiling heat transfer structures, offers a high processing flexibility and can provide lattice structures with a high surface-to-volume ratio. As an important part of the phased array radar, the plentiful transmit/receive (T/R) modules can generate considerable heat. Targeting this local overheating problem, this study discusses the pass design, the optimal formation process, and boiling heat transfer performance of microchannel liquid-cooled plates based on L-PBF additive manufacturing technology. The optimum design and process parameters were obtained by performing basic channel experiments. On this basis, the design and formation experiments of the microchannel structure were performed, and then the porosity and pore morphology of microchannel liquid-cooled plate samples were analysed. The boiling heat transfer experiments were conducted with deionised water, and the boiling heat transfer characteristics were compared with the saturated boiling curve of a traditional copper-tube liquid-cooled plate. The average wall temperature of the designed samples decreased by 4% compared with that of the traditional liquid-cooled plate under the same heat flow density the value reduced from 111.9 °C to 108.2 °C. Furthermore, within the same optimal boiling temperature range, the average heat flow densities of all the prepared samples increased by >60% compared with those of the traditional liquid-cooled plate the value increased from minimum 16 W∙cm−2 to maximum 34 W∙cm−2. The self-supporting microchannel structure can considerably improve the heat dissipation effect of T/R modules and solve the local overheating problem.