To obtain the closed-form forward kinematics of parallel robots, researchers use algebra-based method to transform and simplify the constraint equations. However, this method requires a complicated derivation that leads to high-order univariate variable equations. In fact, some particular mechanisms, such as Delta, or H4 possess many invariant geometric properties during movement. This suggests that one might be able to transform and reduce the problem using geometric approaches. Therefore, a simpler and more efficient solution might be found. Based on this idea, we developed a new geometric approach called geometric forward kinematics (GFK) to obtain the closed-form solutions of H4 forward kinematics in this paper. The result shows that the forward kinematics of H4 yields an eighth degree univariate polynomial, compared with earlier reported 16th degree. Thanks to its clear physical meaning, an intensive discussion about the solutions is presented. Results indicate that a general H4 robot can have up to eight nonrepeated real solutions for its forward kinematics. For a specific configuration of H4, the nonrepeated number of real roots could be restricted to only two, four, or six. Two traveling plate configurations are discussed in this paper as two typical categories of H4. A numerical analysis was also performed for this new method.
10 January 2020 in Journal of Mechanisms and Robotics
Based on observations from nature, tails are believed to help animals achieve highly agile motions. Traditional single-link robotic tails serve as a good simplification for both modeling and implementation purposes. However, this approach cannot explain the complicated tail behaviors exhibited in nature where multi-link structures are more commonly observed. Unlike its single-link counterpart, articulated multi-link tails essentially belong to the serial manipulator family which possesses special motion transmission design challenges. To address this challenge, a cable driven hyper-redundant design becomes the most used approach. Limited by cable strength and elastic components, this approach suffers from low frequency response, inadequate generated inertial loading, and fragile hardware, which are all critical drawbacks for robotic tails design. To solve these structure related shortcomings, a multi-link robotic tail made up of rigid links is proposed. The new structure takes advantage of the traditional hybrid mechanism architecture, but utilizes rigid mechanisms to couple the motions between the i-th and the (i+1)-th link rather than using cable actuation. Consequently, the overall tail becomes a rigid mechanism which achieves quasi-uniform spatial bending for each segment and highly dynamic motions. The mechanism and detailed design of this new robotic tail are presented. The kinematic model was developed and an optimization process was conducted to reduce the bending non-uniformity for the tail. Based on this design optimization, the dynamic model of the mechanism is significantly simplified. A prototype was integrated to verify the proposed mechanism's unique mobility.
15 March 2021 in Journal of Mechanisms and Robotics
An extensible continuum manipulator (ECM) has specific advantages over its nonextensible counterparts. For instance, in certain applications, such as minimally invasive surgery or pipe inspection, the base motion might be limited or disallowed. The additional extensibility provides the robot with more dexterous manipulation and a larger workspace. Existing continuum robot designs achieve extensibility mainly through artificial muscle/pneumatic, extensible backbone, concentric tube, and base extension, etc. This article proposes a new way to achieve this additional motion degree-of-freedom by taking advantage of the rigid coupling hybrid mechanism concept and a flexible parallel mechanism. More specifically, a rack and pinion set is used to transmit the motion of the i-th subsegment to drive the (i+1)-th subsegment. A six-chain flexible parallel mechanism is used to generate the desired spatial bending and one extension mobility for each subsegment. This way, the new manipulator can achieve tail-like spatial bending and worm-like extension at the same time. Simplified kinematic analyses are conducted to estimate the workspace and the motion nonuniformity. A proof-of-concept prototype was integrated to verify the mechanism’s mobility and to evaluate the kinematic model accuracy. The results show that the proposed mechanism achieved the desired mobilities with a maximum extension ratio of 32.2% and a maximum bending angle of 80 deg.
This paper presents the development of a new robotic tail based on a novel cable-driven universal joint mechanism. The novel joint mechanism is synthesized by geometric reasoning to achieve the desired cable length invariance property, wherein the mechanism maintains a constant length for the driving cables under universal rotation. This feature is preferable because it allows for the bidirectional pulling of the cables which reduces the requisite number of actuators. After obtaining this new joint mechanism, a serpentine robotic tail with fewer actuators, simpler controls, and a more robust structure is designed and integrated. The new tail includes two independent macro segments (2 degrees of freedom each) to generate more complex shapes (4 degrees of freedom total), which helps with improving the dexterity and versatility of the robot. In addition, the pitch bending and yaw bending of the tail are decoupled due to the perpendicular joint axes. The kinematic modeling, dynamic modeling, and workspace analysis are then explained for the new robotic tail. Three experiments focusing on statics, dynamics, and dexterity are conducted to validate the mechanism and evaluate the new robotic tail's performance.
6 March 2020 in Journal of Mechanisms and Robotics
This paper presents the design, dynamic modeling, and integration of a single degree of freedom (DOF) robotic leg mechanism intended for tailed quadruped locomotion. The design employs a lightweight six-bar linkage that couples the hip and knee flexion/extension joints mechanically, requiring only a single degree of actuation. By utilizing a parametric optimization, a unique topological arrangement is achieved that results in a foot trajectory that is well suited for dynamic gaits including trot-running, bounding, and galloping. Furthermore, a singular perturbation is introduced to the hybrid dynamic framework to address the lack of robust methods that provide a solution for the differential algebraic equations (DAEs) that characterize closed kinematic chain (CKC) structures as well as the hybrid nature of legged locomotion. By approximating the system dynamics as ordinary differential equations (ODEs) and asymptotically driving the constraint error to zero, CKCs can adopt existing real-time model-based/model-predictive/hybrid-control frameworks. The dynamic model is verified through simulations and the foot trajectory was experimentally validated. Preliminary open-loop planar running demonstrated speeds up to 3.2 m/s. These advantages, accompanied by low-integration costs, warrant this leg as a robust, effective platform for future tailed quadruped research.