Mehdi Eskandarzade

Dr. Mehdi Eskandarzade

orcid

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2017 in Journal of Alloys and Compounds
Verified
Journal Article
Open access
MEMehdi Eskandarzade
Mehdi Eskandarzade
AMAbolfazl Masoumi
Abolfazl Masoumi
GFGhader Faraji
Ghader Faraji
Mahdi Mohammad-pourMahdi Mohammad-pour
Mahdi Mohammad-pour
XYXinjie Sabrina Yan
Xinjie Sabrina Yan
This paper was accepted for publication in the journal Journal of Alloys and Compounds and the definitive published version is available at http://dx.doi.org/10.1016/j.jallcom.2016.10.296.High pressure torsion (HPT) is one of the most important and effective severe plastic deformation (SPD) processes for producing nanostructured (NS) and ultrafine grained (UFG) metals. Whereas HPT presents excellent mechanical properties, its applications are limited to small disk-shaped samples. In this study a new design of incremental HPT (IHPT) process entitled SIHPT is developed which is much convenient for the production of large NS and UFG metallic rods. In this new design, some steppers along the length of the rod-shaped sample are used while applying an axial load from two ends of it. Step twisting of stepper parts with simultaneous axial loads extend the deformed region to the whole length of the sample. The five turn IHPT process was applied to a 50 mm length and 10 mm diameter pure copper sample and microstructure, and mechanical properties were evaluated. The microstructural study of SIHPT processed samples using TEM and EBSD micrographs clearly reflected the NS sample having an average grain size of less than 100 nm. Also, microhardness measurements showed that the sample has fairly good homogeneity through both axial and radial directions. Besides, tensile test measurements indicate that there is about four times improvement in yield strength of nanostructured sample compared to unprocessed metal which is accompanied with satisfactory ductility as a result of high hydrostatic compressive stresses

1 June 2017 in International Journal of Adhesion and Adhesives
Verified
Journal Article
Closed access
KBKarim Osouli Bostanabad
Karim Osouli Bostanabad
ATAbolfazl Tutunchi
Abolfazl Tutunchi
MEMehdi Eskandarzade
Mehdi Eskandarzade

21 December 2009 in Ultrasonics
Verified
Journal Article
Closed access
MEMehdi Eskandarzade
Mehdi Eskandarzade
TKT. Kundu
T. Kundu
NLN. Liebeaux
N. Liebeaux
DPD. Placko
D. Placko
FMF. Mobadersani
F. Mobadersani

1 August 2022 in Journal of Pipeline Systems Engineering and Practice
Verified
Journal Article
Closed access
PDF file
MEMehdi Eskandarzade
Mehdi Eskandarzade
RSReza Shahrivar
Reza Shahrivar
R.M. Chandima RatnayakeR.M. Chandima Ratnayake
R.M. Chandima Ratnayake
UBUmair Niaz Bukhari
Umair Niaz Bukhari
Risk-based inspection (RBI) analysis and recommendations provide an optimal strategy for inspection planning in the oil, gas, and petrochemical industries. The RBI analysis and recommendations are performed based on qualitative, semiquantitative, and quantitative approaches. The suggested approach complements the qualitative RBI analysis approaches, as the existing techniques result in suboptimal inspection intervals. Although quantitative RBI methods have been well-developed for above-ground (and topside) piping and equipment, there is a significant need for developing quantitative or semiquantitative approaches for underground (or subsea) hazardous liquid pipelines. This manuscript presents a new approach to assess risk for liquid pipelines. The proposed method encompasses both time-dependent and time-independent damage types. In a proposed approach, for risk analysis of time-independent damages, an improved Kent Muhlbauer method is suggested. The improved Kent Muhlbauer method uses logical weight factors and modification factors which help to obtain repeatable results. In addition, the general failure frequency method as proposed in API-RP 581 is suggested for time-dependent damage types. The combination of these two methods constitutes the core of the proposed risk assessment algorithm of this study. The proposed method was implemented in a pipeline integrity assessment project. The overall study findings revealed that the results are satisfactory and reasonable and have a practical significance for inspection planning engineers.

15 August 2008 in Asian Journal of Scientific Research
Verified
Journal Article
Closed access
ADA. Doniavi
A. Doniavi
MEMehdi Eskandarzade
Mehdi Eskandarzade
AAA. Abdi
A. Abdi
ATA. Totonchi
A. Totonchi

1 May 2020 in Journal of Pipeline Systems Engineering and Practice
Verified
Journal Article
Closed access
ATAbolfazl Tutunchi
Abolfazl Tutunchi
MEMehdi Eskandarzade
Mehdi Eskandarzade
KOKarim Osouli-Bostanabad
Karim Osouli-Bostanabad
RSReza Shahrivar
Reza Shahrivar
The integrity management activities should aim to ensure that all safety requirements are maintained within acceptable levels. A fully comprehensive inspection of all equipment in a unit/facility is not a cost-effective method. Therefore, in recent approaches, the budget and resources are assigned in a way to only fully cover the equipment with a medium-high or high-risk level, while preserving a sufficient effort on lower risk components. In this regard the risk assessment procedure of the underground polyethylene (PE) natural gas piping networks has not been developed yet. Hence, the current study was conducted to (1) identify the credible failure mechanisms in urban natural gas PE piping systems and (2) evaluate the probability of failures and consequences of failures for various failure scenarios. The ultimate goal was to find the critical piping segments. It proposed a methodology to prioritize technical inspection activities for different segments in the urban natural gas piping systems based on their risk levels. The procedure was applied in the piping network of a small city (Ardabil, Iran) to identify the critical segments. Relevant recommendations were made after successfully detecting these segments.