Modern electronic textiles are moving towards flexible wearable textiles, so-called e-textiles that have micro-electronic elements embedded onto the textile fabric that can be used for varied classes of functionalities. There are different methods of integrating rigid microelectronic components into/onto textiles for the development of smart textiles, which include, but are not limited to, physical, mechanical, and chemical approaches. The integration systems must satisfy being flexible, lightweight, stretchable, and washable to offer a superior usability, comfortability, and non-intrusiveness. Furthermore, the resulting wearable garment needs to be breathable. In this review work, three levels of integration of the microelectronics into/onto the textile structures are discussed, the textile-adapted, the textile-integrated, and the textile-based integration. The textile-integrated and the textile-adapted e-textiles have failed to efficiently meet being flexible and washable. To overcome the above problems, researchers studied the integration of microelectronics into/onto textile at fiber or yarn level applying various mechanisms. Hence, a new method of integration, textile-based, has risen to the challenge due to the flexibility and washability advantages of the ultimate product. In general, the aim of this review is to provide a complete overview of the different interconnection methods of electronic components into/onto textile substrate.

Consumers purchasing textiles usually feel fabrics for its tactile properties indicating that they are interested in comfort properties rather than other properties. During daily activities, low-stress mechanical action like bending, shear, compression, tensile, and hysteresis occurs on clothing. These high sensitive low-stress mechanical properties have influence on movement comfort of the body. This study reports effect of cotton yarn parameters on tactile comfort and low-stress mechanical properties of four knitted fabrics. These fabrics were developed with cotton yarn having different yarn counts; twist, coefficient of mass variation, neps, hairiness, thin and thick places, and strength and elongation. Half-bleach treatment was carried out on the knitted fabrics and the effect of yarn parameters plus their correlation on tactile comfort and low-stress mechanical properties were evaluated. Results statistically analyzed showed that coefficient of friction, surface roughness, tensile, bending, shear, and compression of knitted fabrics were affected by yarn count. However, in wales direction, tensile resilience (RT%) of knitted fabrics had insignificant change with an F-value of 1.110 and p-value of .248. A correlation was also found between fabric smoothness and yarn count at adj. R² = 83.1%. A relationship between yarn parameters and tactile comfort properties was also modeled using equations.

Hybrid composites have proven endless benefits to the research communities in terms of environmental friendliness, mechanical properties, and development of new material. The present work explores the tensile, flexural, impact strengths, and water absorption properties of jute and palm leaf fiber-reinforced hybrid composites. Five types of hybrid composites were fabricated by varying jute and palm leaf fiber percentage of J100:P0, J25:P75, J50:P50, J25:P75, and J0:P100% with a constant weight ratio of polypropylene matrix. The findings showed that jute-palm leaf fiber-reinforced composite had positive effect on tensile, flexural, and impact strength. Experimental results showed that the J25:P75% (jute and palm leaf fiber) exhibited the highest tensile strength of 62.2 MPa and flexural strength of 82.26 MPa due to the optimal interfacial properties between the fibers and matrix. The impact strength of composites increased as the proportion of palm leaf fiber increased. Water absorption increased with jute fiber content, reaching a maximum of 1.26% at composite J100:P0, with lower water absorption at J0:P100% composite due to the higher moisture content of jute fiber.

Owing to environmental concerns caused by the use of synthetic fibers, there is an urgent need to find new eco-friendly fibers. In addition, conventional cellulosic fibers are becoming costly due to an increase in production cost, therefore, sustainable alternative sources of eco-friendly fibers need to be explored. This study investigates the extraction and characterization of fibers from the Cyperus papyrus plant and evaluates its potential as textile fibers. Cyperus papyrus plant fibers were extracted using water retting and alkaline extraction methods and their mechanical, physical, thermal, and chemical properties were studied. The fiber’s chemical composition was established and alkaline extracted fibers contained 61.82% cellulose, 11.82% hemicellulose, 23.6% lignin, 3.86% ash, and 2.75% extractive while the water-retted fibers contained 57.98% cellulose, 13.45% hemicellulose, 25.42% lignin, 6.07% ash, and 3.15% extractive. The fineness of the extracted fibers was 8.38 and 7.31 Tex for water-retted and for alkaline extracted fibers, respectively. The average tensile strength of the extracted fibers ranged from 26.25 to 31.05cN/Tex. The average elongation of the fibers was between 2.02% and 2.79% while its thermal degradation temperature was as high as 150ºC. Compared with conventional fibers, the extracted fibers have the potential of replacing them based on the properties studied.

Plastic has been a dominant material for packaging in recent years but due to its nonbiodegradability, it is causing environmental pollution. Among the plastics used, low-density polyethylene is used abundantly. These plastics can be removed from the environment by recycling into useful products through reinforcing it with natural textile fibers into composite materials. Natural fiber-based composites are ecofriendly and low cost. This research is aimed at manufacturing composite wall tiles from recycled low-density polyethylene reinforced with pineapple leaf fibers (PALF). The PALF was extracted by the retting process followed by mechanical scratching and treated with 5% NaOH to improve the fiber-matrix interaction. The composites were manufactured by the melt-mixing method followed by compression molding. The effects of fiber length and fiber weight proportion on composite properties were investigated using tensile, flexural, impact, and water absorption tests. The study showed that the optimum fiber weight proportion and fiber length for the optimal properties of the composite were achieved at 30% fiber weight proportion and 30 mm fiber length. The maximum tensile strength of 1562 N/mm², flexural strength of 454.9 N/mm², and impact strength of 225.2 J/mm² were obtained. Water absorption of the tiles increased with the increase in both the fiber weight proportion and the fiber length.