This letter presents a circular polarizer using a multilayer frequency selective surface based on split rings bisected by a metal strip. This geometry provides the advantages of both low cross-polarization level and low sensibility with respect to the incidence angle of the ring-based topology. To validate the proposed design, a four-layer prototype to operate in Ka-band has been designed, fabricated, and tested. Experimental results show that axial ratios lower than 3 dB are obtained for angles of incidence as high as 25 ° over the frequency range of 25.5-36.5 GHz.

A new type of wideband dual-input hybrid Doherty outphasing power amplifier (HDO-PA) is developed in which the load-modulation scheme continuously converts as the frequency increase, from the previously reported HDO-PA mode with maximum flat efficiency response versus power to the conventional Doherty PA mode. For a symmetric HDO-PA implementation, this corresponds to the peak-to-backoff fundamental voltage ratio of the auxiliary amplifier linearly varying from 9/7 to 2 with frequency. A transmission-line-based wideband HDO-PA prototype is first established at the current-source reference planes to cover the frequency band from 1.4-GHz to 2.5-GHz. The wideband HDO-PA is implemented next at the package reference planes by synthesizing the wideband combiner circuit required to sustain the intrinsic load-modulation behavior across the entire frequency bandwidth. A 1.4-GHz to 2.5-GHz wideband HDO-PA is fabricated and characterized using both continuous-wave and modulated signals. The 6-dB backoff efficiency varies from 60% to 44% and the maximum power from 44.8 dBm to 42.9 dBm as the frequency increases. When the PA is excited with a 20 MHz bandwidth long-term evolution signal at 1.7 GHz with 6.5 dB peak-to-average-power ratio (PAPR), the PA achieves an average drain efficiency of 50.3% with -32.0 dBc adjacent-channel-power leakage ratio (ACLR) and an average drain efficiency of 47.8% with -54.0 dBc ACLR after digital predistortion linearization.

This letter presents active dual-band frequency selective surfaces (AFSS) with close band spacing based on two switchable ring slots loaded by PIN diode switches. The close band response is achieved by splitting the outer ring slot, and then shifting upward its fundamental resonance beyond the resonance of the inner ring slot. The proposed AFSS can provide four states of operation including lower single-band, upper single-band, dual-band with close band spacing, and reflective mode. Experimental results based on the waveguide simulator show that a frequency ratio of 1.14, with insertion loss lower than 0.82 dB at resonant frequencies, is obtained in the X-band.

This article presents the architecture and design methodology for a new type of dual-band Doherty power amplifier (DB-DPA), referred to as 3-Way DB-DPA, which consists of a main amplifier for each band and an auxiliary amplifier handling both bands. The 3-Way DB-DPA improves the average drain efficiency in concurrent dual-band operation compared to the traditional 2-Way DB-DPA, by avoiding early clipping in the main amplifiers, while benefiting from load—pulling from the auxiliary power amplifier (PA). This improvement is verified in theory and simulation at the current-source reference planes and in measurement with a fabricated 1.5- and 2-GHz dual-band PA. A statistical analysis using 2-D continuous-wave (CW) signals with long-term evolution (LTE) probability distribution functions (PDFs) is performed and demonstrated an improvement in the concurrent average efficiency by 15 percentage points compared to the conventional 2-Way DB-DPA. In nonconcurrent operation, the measured CW drain efficiency in the lower band (1.5 GHz) is 82.8% at peak and 66.6% at 9.6-dB backoff, and the measured CW drain efficiency in the upper band (2.0 GHz) is 70.0% at peak and 48.4% at 9.4-dB backoff. The CW concurrent-balanced drain efficiency reaches 66.2/52.0% in the 3-Way DB-DPA at 3-/6-dB backoff. In single-band operation at 1.5/2.0 GHz, the average power and average drain efficiency after linearization by digital predistortion (DPD) are 35.1/37.4 dBm and 65.0/53.7%, respectively, for an LTE signal with 10-MHz bandwidth and 6.1-dB peak-to-average power ratio (PAPR). In concurrent operation, the 3-Way DB-DPA is driven by two 10-MHz LTE uncorrelated signals at 1.5 GHz with 6.86-dB PAPR and at 2.0 GHz with 6.26-dB PAPR, and the average total power and average concurrent drain efficiency after DPD are 37.5 dBm and 54.24%, respectively.

Reconfigurable spiraphase-type reflectarrays based on ring slot resonators with switchable radial stubs are presented. The mathematical model of the infinite array was used to optimize the spiraphase-type element at 36.5 GHz. The optimization goals were to minimize the dissipative loss in the p-i-n diode switches and to reduce the cross-polarization radiation. The mathematical model of the finite array was then used to simulate the radiation characteristics of a reconfigurable reflectarray with 277 optimized elements for different scanning elevation angles θ_ο. The calculated aperture efficiencies were 0.42, 0.40, 0.36, 0.25, 0.16, and 0.12 for θ_ο equal to 0°, 20°, 30°, 40°, 45°, and 50°, respectively. For validation of the numerical simulations, three 277-element reflectarrays for fixed θ_ο of 0°, 20°, and 30° were designed. Metal strips and open circuits were used instead of the forward and reverse p-i-n diode states, respectively. These reflectarrays were then fabricated and tested, demonstrating aperture efficiencies equal to 0.41, 0.40, and 0.28 for θ_ο equal to 0°, 20°, and 30°, respectively. Measured characteristics agreed satisfactorily with theoretical predictions.