Su-Jin Jang

Ms. Su-Jin Jang


Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 November 2021 in Energies
Verified
Journal Article
Open access
PDF file
SJSu-Jin Jang
Su-Jin Jang
JLJeong Han Lee
Jeong Han Lee
SKSeo Hui Kang
Seo Hui Kang
YKYun Chan Kang
Yun Chan Kang
KRKwang Chul Roh
Kwang Chul Roh
The development of supercapacitors with high volumetric capacitance and high-rate performance has been an important research topic. Activated carbon (AC), which is a widely used material for supercapacitor electrodes, has different surface structures, porosities, and electrochemical properties. However, the low conductivity of the electrode material is a major problem for the efficient use of AC in supercapacitors. To tackle this challenge, we prepared conductive, additive-free electrodes for supercapacitors by a simple one-pot treatment of AC with melamine (nitrogen source), pitch, and sucrose (both carbon source). Nitrogen-doped and carbon-coated AC was successfully generated after high-temperature heat treatment. The AC was doped with approximately 0.5 at.% nitrogen, and coated with carbon leading to a decreased oxygen content. Thin carbon layers (~10 nm) were coated onto the outer surface of the AC, as shown in TEM images. The modification of the AC surface with a sucrose source is favorable, as it increases the electrical conductivity of AC up to 3.0 S cm−1, which is 4.3 times higher than in unmodified AC. The electrochemical performance of the modified AC was evaluated by conducting agent-free electrode. Although the obtained samples had slightly reduced surface areas after the surface modification, they maintained a high specific surface area of 1700 m2 g−1. The supercapacitor delivered a specific capacitance of 70.4 F cc−1 at 1 mA cm−1 and achieved 89.8% capacitance retention even at a high current density of 50 mA cm−2. Furthermore, the supercapacitor delivered a high energy density of 24.5 Wh kg−1 at a power density of 4650 W kg−1. This approach can be extended for a new strategy for conductivity additive-free electrodes in, e.g., supercapacitors, batteries, and fuel cells.

30 September 2021 in Catalysts
Verified
Journal Article
Open access
PDF file
SJSu-Jin Jang
Su-Jin Jang
YKYun Chan Kang
Yun Chan Kang
JHJin-Su Hyun
Jin-Su Hyun
Tae Ho ShinTae Ho Shin
Tae Ho Shin
Young Wook LeeYoung Wook Lee
Young Wook Lee
KRKwang Chul Roh
Kwang Chul Roh
The durability of catalysts in fuel cells is a longstanding issue that needs to be resolved. Catalyst stability of the fuel cell has always been a problem, studies are underway to address them. Herein, to address this issue, we synthesize a hybrid structure consisting of SP carbon (SP) as the graphitic carbon and TiO2 as the metal oxide using a microwave method for use as a support for Pt nanoparticles. Anatase TiO2 and Pt nanoparticles with sizes of ~5 and 3.5 ± 1.4 nm, respectively, are uniformly dispersed on a modified graphitic SP carbon support (Pt-TiO2-SP). This supported Pt catalyst exhibits significantly improves durability in the oxygen reduction reaction (ORR). Furthermore, the Pt-TiO2-SP carbon hybrid catalyst manifests superior electrocatalytic stability and higher onset potential in ORR than those exhibited by Pt-SP carbon without TiO2. Pt-TiO2-SP exhibits an activity loss of less than 68 mV after 5000 electrochemical cycles, whereas an activity loss of ~100 mV is observed for Pt-SP carbon in a stability test. These results suggest that the strong metal–support interaction in TiO2-supported Pt catalyst significantly enhances the activity of Pt nanocatalyst.