Herein, the fabrication of a novel highly sensitive and fast hydrogen (H2) gas sensor, based on the Ta2O5 Schottky diode, is described. First, Ta2O5 thin films are deposited on silicon carbide (SiC) and silicon (Si) substrates via a radio frequency (RF) sputtering method. Then, Pd and Ni are respectively deposited on the front and back of the device. The deposited Pd serves as a H2 catalyst, while the Ni functions as an Ohmic contact. The devices are then tested under various concentrations of H2 gas at operating temperatures of 300, 500, and 700 °C. The results indicate that the Pd/Ta2O5 Schottky diode on the SiC substrate exhibits larger concentration and temperature sensitivities than those of the device based on the Si substrate. In addition, the optimum operating temperature of the Pd/Ta2O5 Schottky diode for use in H2 sensing is shown to be about 300 °C. At this optimum temperature, the dynamic responses of the sensors towards various concentrations of H2 gas are then examined under a constant bias current of 1 mA. The results indicate a fast rise time of 7.1 s, and a decay of 18 s, for the sensor based on the SiC substrate.
In this work, forming-free and self-limited resistive switching characteristics are demonstrated in the transition-metal-chalcogenide-based conductive bridge RAM devices. Owing to the choice of a suitable solid electrolyte, the proposed WTe 2 -based devices present excellent switching characteristics offering highly desirable attributes such as high pulse endurance (>2×10 7 cycles) and stable data retention (10 years at 72°C). The devices also present excellent device-to-device and cycle-to-cycle uniformity which is highly desirable for the practical implementation of resistive random access memory (RRAM) devices in large crossbar arrays. The demonstration of robust and highly repeatable multilevel switching further provides multibit data storage capability for high-density memory.
A double stacked monochalcogenide GeS-based conducting-bridge random access memory (CBRAM) device with a IGZO buffer layer is investigated for highly improved resistive memory characteristics. The IGZO/GeS double layer is found to provide the CBRAM with a markedly improved sub-1V DC set/reset-voltage distributions (<±0.1 V variation). High endurance (>107 cycles) and retention (>105 s at 85 °C) performance are also achieved. The metal ion diffusion and migration rates in the solid electrolytes along with the redox reaction rates at the electrodes determine the respective resistive switching (RS) mechanism in the CBRAM device. Considering this fact, it is proposed that Ag diffusion into IGZO creates a virtual electrode, when coupled with strong ionic transport in GeS, consistently mediate the formation/dissolution of Ag filament there, thus reducing switching variation. Understanding the RS mechanism based on the materials' physical and chemical properties and tailoring the device structure allow an optimal control over cycle to cycle and device to device variability. The findings show that this material combination or similar oxide/chalcogenide stacks may offer a facile means for mitigating CBRAM variability.
The electronic properties of single-layer, CVD-grown graphene were modulated by deep ultraviolet (DUV) light irradiation in different radiation environments. The graphene field-effect transistors (GFETs), exposed to DUV in air and pure O2, exhibited p-type doping behavior, whereas those exposed in vacuum and pure N2 gas showed n-type doping. The degree of doping increased with DUV exposure time. However, n-type doping by DUV in vacuum reached saturation after 60 min of DUV irradiation. The p-type doping by DUV in air was observed to be quite stable over a long period in a laboratory environment and at higher temperatures, with little change in charge carrier mobility. The p-doping in pure O2 showed ~15% de-doping over 4 months. The n-type doping in pure N2 exhibited a high doping effect but was highly unstable over time in a laboratory environment, with very marked de-doping towards a pristine condition. A lateral pn-junction of graphene was successfully implemented by controlling the radiation environment of the DUV. First, graphene was doped to n-type by DUV in vacuum. Then the n-type graphene was converted to p-type by exposure again to DUV in air. The n-type region of the pn-junction was protected from DUV by a thick double-coated PMMA layer. The photocurrent response as a function of Vg was investigated to study possible applications in optoelectronics.
18 November 2024 in ACS Applied Electronic Materials